Vulićević, Zoran

Link to this page

Authority KeyName Variants
e927de9f-5390-4ea6-beac-e4c026a02b4e
  • Vulićević, Zoran (27)
Projects

Author's Bibliography

Prosthetics in paediatric dentistry

Vulićević, Zoran; Beloica, Miloš; Kosanović, Dušan; Radović, Ivana; Juloski, Jelena; Ivanović, Dragan

(Udruženje stomatologa Balkana, 2017)

TY  - JOUR
AU  - Vulićević, Zoran
AU  - Beloica, Miloš
AU  - Kosanović, Dušan
AU  - Radović, Ivana
AU  - Juloski, Jelena
AU  - Ivanović, Dragan
PY  - 2017
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/2246
AB  - Premature loss of teeth in children may lead to both functional and esthetic problems. Missing teeth in both anterior and posterior regions may cause malfunctions in mastication and proper pronunciation. If the missing teeth are not replaced, further complications may occur, including adjacent tooth migration, loss of alveolar bone, and irregular occlusion. Considering the sensitive nature of children, loss of teeth may cause the development of insecurities and low self esteem problems. Due to dynamic nature of growth in children and adolescents, prosthetic appliances must not hinder development of orofacial system, and must meet adequate esthetic and functional standards. Dental prosthetic appliances in paediatrics must be planned with respect to the special conditions that led to tooth loss or damage. Multi-disciplinary approach is needed, under constant supervision of paediatric dentist and orthodontist, as well as regular checkups with clinical and radiographical examinations.
PB  - Udruženje stomatologa Balkana
T2  - Balkan Journal of Dental Medicine
T1  - Prosthetics in paediatric dentistry
VL  - 21
IS  - 2
SP  - 78
EP  - 82
DO  - 10.1515/bjdm-2017-0012
ER  - 
@article{
author = "Vulićević, Zoran and Beloica, Miloš and Kosanović, Dušan and Radović, Ivana and Juloski, Jelena and Ivanović, Dragan",
year = "2017",
abstract = "Premature loss of teeth in children may lead to both functional and esthetic problems. Missing teeth in both anterior and posterior regions may cause malfunctions in mastication and proper pronunciation. If the missing teeth are not replaced, further complications may occur, including adjacent tooth migration, loss of alveolar bone, and irregular occlusion. Considering the sensitive nature of children, loss of teeth may cause the development of insecurities and low self esteem problems. Due to dynamic nature of growth in children and adolescents, prosthetic appliances must not hinder development of orofacial system, and must meet adequate esthetic and functional standards. Dental prosthetic appliances in paediatrics must be planned with respect to the special conditions that led to tooth loss or damage. Multi-disciplinary approach is needed, under constant supervision of paediatric dentist and orthodontist, as well as regular checkups with clinical and radiographical examinations.",
publisher = "Udruženje stomatologa Balkana",
journal = "Balkan Journal of Dental Medicine",
title = "Prosthetics in paediatric dentistry",
volume = "21",
number = "2",
pages = "78-82",
doi = "10.1515/bjdm-2017-0012"
}
Vulićević, Z., Beloica, M., Kosanović, D., Radović, I., Juloski, J.,& Ivanović, D.. (2017). Prosthetics in paediatric dentistry. in Balkan Journal of Dental Medicine
Udruženje stomatologa Balkana., 21(2), 78-82.
https://doi.org/10.1515/bjdm-2017-0012
Vulićević Z, Beloica M, Kosanović D, Radović I, Juloski J, Ivanović D. Prosthetics in paediatric dentistry. in Balkan Journal of Dental Medicine. 2017;21(2):78-82.
doi:10.1515/bjdm-2017-0012 .
Vulićević, Zoran, Beloica, Miloš, Kosanović, Dušan, Radović, Ivana, Juloski, Jelena, Ivanović, Dragan, "Prosthetics in paediatric dentistry" in Balkan Journal of Dental Medicine, 21, no. 2 (2017):78-82,
https://doi.org/10.1515/bjdm-2017-0012 . .
3

Influence of luting agent translucency on fiber post retention

Juloski, Jelena; Goracci, Cecilia; Tsintsadze, Nino; Carrabba, Michele; Vichi, Alessandro; Vulićević, Zoran; Ferrari, Marco

(Wiley, Hoboken, 2015)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Goracci, Cecilia
AU  - Tsintsadze, Nino
AU  - Carrabba, Michele
AU  - Vichi, Alessandro
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2015
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1978
AB  - The aim was to assess the influence of cement translucency on the retentive strength of luted fiber posts. Twenty extracted human premolars were randomly divided into four equal groups, based on the combinations of materials to be tested. Two post types of the same size, shape, and chemical composition, but different light-transmission properties [Translucent post (TP) and Opaque post (OP)] were selected. The two post types were luted using the etch-and-rinse, light-curing adhesive in combination with two shades of the same resin cement of markedly different light-transmitting ability [Transparent shade (TS) and Opaque shade (OS)]. Early post retention was assessed using the thin-slice push-out test. Post type did not significantly influence post retention; however, cement translucency emerged as a relevant factor in intraradicular cementation, with the TS achieving higher push-out strengths. The between-factor interaction was also statistically significant; specifically, OP-OS yielded significantly lower retentive strengths than all the other groups. Post translucency did not influence post retention, provided that a highly translucent cement was utilized for luting.
PB  - Wiley, Hoboken
T2  - European Journal of Oral Sciences
T1  - Influence of luting agent translucency on fiber post retention
VL  - 123
IS  - 2
SP  - 116
EP  - 121
DO  - 10.1111/eos.12174
ER  - 
@article{
author = "Juloski, Jelena and Goracci, Cecilia and Tsintsadze, Nino and Carrabba, Michele and Vichi, Alessandro and Vulićević, Zoran and Ferrari, Marco",
year = "2015",
abstract = "The aim was to assess the influence of cement translucency on the retentive strength of luted fiber posts. Twenty extracted human premolars were randomly divided into four equal groups, based on the combinations of materials to be tested. Two post types of the same size, shape, and chemical composition, but different light-transmission properties [Translucent post (TP) and Opaque post (OP)] were selected. The two post types were luted using the etch-and-rinse, light-curing adhesive in combination with two shades of the same resin cement of markedly different light-transmitting ability [Transparent shade (TS) and Opaque shade (OS)]. Early post retention was assessed using the thin-slice push-out test. Post type did not significantly influence post retention; however, cement translucency emerged as a relevant factor in intraradicular cementation, with the TS achieving higher push-out strengths. The between-factor interaction was also statistically significant; specifically, OP-OS yielded significantly lower retentive strengths than all the other groups. Post translucency did not influence post retention, provided that a highly translucent cement was utilized for luting.",
publisher = "Wiley, Hoboken",
journal = "European Journal of Oral Sciences",
title = "Influence of luting agent translucency on fiber post retention",
volume = "123",
number = "2",
pages = "116-121",
doi = "10.1111/eos.12174"
}
Juloski, J., Goracci, C., Tsintsadze, N., Carrabba, M., Vichi, A., Vulićević, Z.,& Ferrari, M.. (2015). Influence of luting agent translucency on fiber post retention. in European Journal of Oral Sciences
Wiley, Hoboken., 123(2), 116-121.
https://doi.org/10.1111/eos.12174
Juloski J, Goracci C, Tsintsadze N, Carrabba M, Vichi A, Vulićević Z, Ferrari M. Influence of luting agent translucency on fiber post retention. in European Journal of Oral Sciences. 2015;123(2):116-121.
doi:10.1111/eos.12174 .
Juloski, Jelena, Goracci, Cecilia, Tsintsadze, Nino, Carrabba, Michele, Vichi, Alessandro, Vulićević, Zoran, Ferrari, Marco, "Influence of luting agent translucency on fiber post retention" in European Journal of Oral Sciences, 123, no. 2 (2015):116-121,
https://doi.org/10.1111/eos.12174 . .
4
5
4

The application of air abrasion in dentistry

Mandinić, Zoran; Vulićević, Zoran; Beloica, Miloš; Radović, Ivana; Mandić, Jelena; Carević, Momir; Tekić, Jasmina

(Srpsko lekarsko društvo, Beograd, 2014)

TY  - JOUR
AU  - Mandinić, Zoran
AU  - Vulićević, Zoran
AU  - Beloica, Miloš
AU  - Radović, Ivana
AU  - Mandić, Jelena
AU  - Carević, Momir
AU  - Tekić, Jasmina
PY  - 2014
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1920
AB  - One of the main objectives of contemporary dentistry is to preserve healthy tooth structure by applying techniques of noninvasive treatment. Air abrasion is a minimally invasive non mechanical technique of tooth preparation that uses kinetic energy to remove carious tooth structure. A powerful narrow stream of moving aluminum-oxide particles hit the tooth surface and they abrade it without heat, vibration or noise. Variables that affect speed of cutting include air pressure, particle size, powder flow, tip's size, angle and distance from the tooth. It has been proposed that air abrasion can be used to diagnose early occlusal-surface lesions and treat them with minimal tooth preparation using magnifier. Reported advantages of air abrasion include reduced noise, vibration and sensitivity. Air abrasion cavity preparations have more rounded internal contours than those prepared with straight burs. This may increase the longevity of placed restorations because it reduces the incidence of fractures and a consequence of decreased internal stresses. However, air abrasion cannot be used for all patients, i.e. in cases involving severe dust allergy, asthma, chronic obstructive lung disease, recent extraction or other oral surgery, open wounds, advanced periodontal disease, recent placement of orthodontic appliances and oral abrasions, or subgingival caries removal. Many of these conditions increase the risk of air embolism in the oral soft tissues. Dust control is a challenge, and it necessitates the use of rubber dam, high-volume evacuation, protective masks and safety eyewear for both the patient and the therapist.
AB  - Jedan od osnovnih ciljeva savremene stomatologije jeste očuvanje zdravog zubnog tkiva primenom preventivnih metoda i tehnika neinvazivnog lečenja. Vazdušna abrazija je minimalno invazivna tehnika preparacije kaviteta koja koristi kinetičku energiju za uklanjanje karijesa. Usmeravanje pravolinijskog mlaza čestica aluminijum- oksida na površinu zuba koja se obrađuje dovodi do abrazije supstrata bez toplote, vibracija i zvuka. Faktori koji utiču na brzinu preparacije uključuju intenzitet vazdušnog pritiska, veličinu čestica abraziva, brzinu protoka čestica, prečnik vrha kanile, veličinu ugla kanile i udaljenost vrha kanile od površine zuba koja se obrađuje. Njena upotreba se savetuje u dijagnostici rane karijesne lezije gleđi na okluzalnim površinama zuba i minimalnoj preparaciji kaviteta. Pojedini autori preporučuju i upotrebu optičkih pomagala. Prednosti tehnike vazdušne abrazije uključuju smanjenje buke, vibracija i operativne osetljivosti, koja je veoma subjektivna i promenljiva kod pacijenata. Kaviteti preparisani vazdušnom abrazijom imaju zaobljene ivice, za razliku od kaviteta preparisanih standardnim tehnikama. To može povećati dugotrajnost postavljenih ispuna, jer se smanjuje mogućnost nastanka njihovog odlamanja, neutralisanjem sila unutrašnjeg napona u poređenju sa stresom koji se javlja kod angularnih preparacija. Primena tehnike vazdušne abrazije je kontraindikovana kod osoba alergičnih na prašinu, obolelih od astme ili hronične opstruktivne bolesti pluća, pacijenata sa postekstrakcionim ranama, parodontopatijom, ortodontskim aparatima ili dubokim karijesom, jer se ovom tehnikom preparacije ne odstranjuje uspešno mekana dentinska struktura. Mnoga ova stanja povećavaju rizik od nastanka vazdušne embolije u mekim oralnim tkivima. Kontrola rasejanja čestica abraziva predstavlja izazov kliničkom stomatologu, a zahteva i primenu koferdama, jakih aspiratora, zaštitnih maski i zaštitnih naočara kako kod pacijenta, tako i kod terapeuta.
PB  - Srpsko lekarsko društvo, Beograd
T2  - Srpski arhiv za celokupno lekarstvo
T1  - The application of air abrasion in dentistry
T1  - Primena vazdušne abrazije u stomatologiji
VL  - 142
IS  - 1-2
SP  - 99
EP  - 105
DO  - 10.2298/SARH1402099M
ER  - 
@article{
author = "Mandinić, Zoran and Vulićević, Zoran and Beloica, Miloš and Radović, Ivana and Mandić, Jelena and Carević, Momir and Tekić, Jasmina",
year = "2014",
abstract = "One of the main objectives of contemporary dentistry is to preserve healthy tooth structure by applying techniques of noninvasive treatment. Air abrasion is a minimally invasive non mechanical technique of tooth preparation that uses kinetic energy to remove carious tooth structure. A powerful narrow stream of moving aluminum-oxide particles hit the tooth surface and they abrade it without heat, vibration or noise. Variables that affect speed of cutting include air pressure, particle size, powder flow, tip's size, angle and distance from the tooth. It has been proposed that air abrasion can be used to diagnose early occlusal-surface lesions and treat them with minimal tooth preparation using magnifier. Reported advantages of air abrasion include reduced noise, vibration and sensitivity. Air abrasion cavity preparations have more rounded internal contours than those prepared with straight burs. This may increase the longevity of placed restorations because it reduces the incidence of fractures and a consequence of decreased internal stresses. However, air abrasion cannot be used for all patients, i.e. in cases involving severe dust allergy, asthma, chronic obstructive lung disease, recent extraction or other oral surgery, open wounds, advanced periodontal disease, recent placement of orthodontic appliances and oral abrasions, or subgingival caries removal. Many of these conditions increase the risk of air embolism in the oral soft tissues. Dust control is a challenge, and it necessitates the use of rubber dam, high-volume evacuation, protective masks and safety eyewear for both the patient and the therapist., Jedan od osnovnih ciljeva savremene stomatologije jeste očuvanje zdravog zubnog tkiva primenom preventivnih metoda i tehnika neinvazivnog lečenja. Vazdušna abrazija je minimalno invazivna tehnika preparacije kaviteta koja koristi kinetičku energiju za uklanjanje karijesa. Usmeravanje pravolinijskog mlaza čestica aluminijum- oksida na površinu zuba koja se obrađuje dovodi do abrazije supstrata bez toplote, vibracija i zvuka. Faktori koji utiču na brzinu preparacije uključuju intenzitet vazdušnog pritiska, veličinu čestica abraziva, brzinu protoka čestica, prečnik vrha kanile, veličinu ugla kanile i udaljenost vrha kanile od površine zuba koja se obrađuje. Njena upotreba se savetuje u dijagnostici rane karijesne lezije gleđi na okluzalnim površinama zuba i minimalnoj preparaciji kaviteta. Pojedini autori preporučuju i upotrebu optičkih pomagala. Prednosti tehnike vazdušne abrazije uključuju smanjenje buke, vibracija i operativne osetljivosti, koja je veoma subjektivna i promenljiva kod pacijenata. Kaviteti preparisani vazdušnom abrazijom imaju zaobljene ivice, za razliku od kaviteta preparisanih standardnim tehnikama. To može povećati dugotrajnost postavljenih ispuna, jer se smanjuje mogućnost nastanka njihovog odlamanja, neutralisanjem sila unutrašnjeg napona u poređenju sa stresom koji se javlja kod angularnih preparacija. Primena tehnike vazdušne abrazije je kontraindikovana kod osoba alergičnih na prašinu, obolelih od astme ili hronične opstruktivne bolesti pluća, pacijenata sa postekstrakcionim ranama, parodontopatijom, ortodontskim aparatima ili dubokim karijesom, jer se ovom tehnikom preparacije ne odstranjuje uspešno mekana dentinska struktura. Mnoga ova stanja povećavaju rizik od nastanka vazdušne embolije u mekim oralnim tkivima. Kontrola rasejanja čestica abraziva predstavlja izazov kliničkom stomatologu, a zahteva i primenu koferdama, jakih aspiratora, zaštitnih maski i zaštitnih naočara kako kod pacijenta, tako i kod terapeuta.",
publisher = "Srpsko lekarsko društvo, Beograd",
journal = "Srpski arhiv za celokupno lekarstvo",
title = "The application of air abrasion in dentistry, Primena vazdušne abrazije u stomatologiji",
volume = "142",
number = "1-2",
pages = "99-105",
doi = "10.2298/SARH1402099M"
}
Mandinić, Z., Vulićević, Z., Beloica, M., Radović, I., Mandić, J., Carević, M.,& Tekić, J.. (2014). The application of air abrasion in dentistry. in Srpski arhiv za celokupno lekarstvo
Srpsko lekarsko društvo, Beograd., 142(1-2), 99-105.
https://doi.org/10.2298/SARH1402099M
Mandinić Z, Vulićević Z, Beloica M, Radović I, Mandić J, Carević M, Tekić J. The application of air abrasion in dentistry. in Srpski arhiv za celokupno lekarstvo. 2014;142(1-2):99-105.
doi:10.2298/SARH1402099M .
Mandinić, Zoran, Vulićević, Zoran, Beloica, Miloš, Radović, Ivana, Mandić, Jelena, Carević, Momir, Tekić, Jasmina, "The application of air abrasion in dentistry" in Srpski arhiv za celokupno lekarstvo, 142, no. 1-2 (2014):99-105,
https://doi.org/10.2298/SARH1402099M . .
3
1
1

Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser

Beloica, Miloš; Vulićević, Zoran; Mandinić, Zoran; Radović, Ivana; Jovičić, Olivera; Carević, Momir; Tekić, Jasmina

(Srpsko lekarsko društvo, Beograd, 2014)

TY  - JOUR
AU  - Beloica, Miloš
AU  - Vulićević, Zoran
AU  - Mandinić, Zoran
AU  - Radović, Ivana
AU  - Jovičić, Olivera
AU  - Carević, Momir
AU  - Tekić, Jasmina
PY  - 2014
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1915
AB  - Goal of contemporary dentistry is to decrease the patient's discomfort during treatment. Dentists aim to achieve maximum with the newly developed dental materials as well as with new cavity preparation techniques in the shortest time span. Since the development of the first constructed borer (drilling machine) for caries removal, the preparation techniques have considerably changed. The progress of dental materials as well as the cavity preparation techniques has led us to contemporary carbide tungsten and diamond borers that are used with obligatory water cooling. The innovation within this field represents newly developed polymer borers that can detect the difference between carious lesions and healthy tooth structure. In this way the cavity preparation may be performed without damaging dental healthy tissue. This is possible owing to their hardness which is lower than the hardness of intact dentin. Polymer borer preparation is painless with less vibration, while the increase in temperature is negligible. Lasers have been used in clinical dentistry since 1980s so it can be said that they represent a new technology. The function of lasers is based on ablation which requires water. Erbium lasers have shown the highest potential with their ability to produce effective ablation of hard dental tissues. Laser application in dentistry requires special training as well as some protective measures. Laser advantages, compared to traditional preparation techniques, involve the absence of vibration, painless preparation, possibility of preparation without anesthetic and easier patient's adjustment to dental intervention which is of importance, especially in pediatric dentistry.
AB  - Savremena stomatologija teži ka što manjoj traumatizaciji pacijenta prilikom rada uz maksimalni učinak. Savremeni materijali uz nove vidove preparacije kaviteta pružaju mogućnost sanacije karijesnih lezija u najkraćem vremenskom roku. Vidovi preparacije kaviteta su se znatno promenili otkako je uvedeno prvo mašinski napravljeno svrdlo za uklanjanje karijesa. Tehnološki napredak materijala za ispune i načina preparacije doveli su do savremenih karbidnih i dijamantskih svrdla koja se koriste uz obavezno vodeno hlađenje. Inovaciju na polju rotirajućih instrumenata predstavljaju polimerna 'pametna' svrdla, koja uklanjaju karijesnu leziju bez mogućnosti povređivanja i uklanjanja zdrave zubne strukture. Ovo je moguće zahvaljujući čvrstoći koju poseduju, koja je manja od čvrstoće zdravog dentina. Zahvaljujući prirodi materijala od kojih su izrađena, ova svrdla omogućuju bezbolniji rad uz manje vibracija i slabije zagrevanje zubne supstance. Laseri su relativno novo tehnološko sredstvo u stomatologiji, a njihova klinička upotreba počela je osamdesetih godina dvadesetog veka. Laseri funkcionišu po principu ablacije, za šta je neophodno prisustvo vode. Najveći potencijal među ispitivanim laserima pokazali su erbijumski laseri, kojima je moguće uraditi efikasnu ablaciju čvrstih zubnih tkiva. Za korišćenje lasera u stomatologiji neophodni su posebna obuka i odgovarajuće mere zaštite. Prednosti lasera u poređenju sa drugim metodama preparacije čvrstih zubnih tkiva su nepostojanje vibracija, bezbolan rad, mogućnost rada bez anestezije i lakše prilagođavanje pacijenta stomatološkim intervencijama, što je veoma značajno u dečjoj stomatologiji.
PB  - Srpsko lekarsko društvo, Beograd
T2  - Srpski arhiv za celokupno lekarstvo
T1  - Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser
T1  - Minimalno invazivna preparacija čvrstih zubnih tkiva savremenim polimernim rotirajućim instrumentima i laserom
VL  - 142
IS  - 5-6
SP  - 365
EP  - 370
DO  - 10.2298/SARH1406365B
ER  - 
@article{
author = "Beloica, Miloš and Vulićević, Zoran and Mandinić, Zoran and Radović, Ivana and Jovičić, Olivera and Carević, Momir and Tekić, Jasmina",
year = "2014",
abstract = "Goal of contemporary dentistry is to decrease the patient's discomfort during treatment. Dentists aim to achieve maximum with the newly developed dental materials as well as with new cavity preparation techniques in the shortest time span. Since the development of the first constructed borer (drilling machine) for caries removal, the preparation techniques have considerably changed. The progress of dental materials as well as the cavity preparation techniques has led us to contemporary carbide tungsten and diamond borers that are used with obligatory water cooling. The innovation within this field represents newly developed polymer borers that can detect the difference between carious lesions and healthy tooth structure. In this way the cavity preparation may be performed without damaging dental healthy tissue. This is possible owing to their hardness which is lower than the hardness of intact dentin. Polymer borer preparation is painless with less vibration, while the increase in temperature is negligible. Lasers have been used in clinical dentistry since 1980s so it can be said that they represent a new technology. The function of lasers is based on ablation which requires water. Erbium lasers have shown the highest potential with their ability to produce effective ablation of hard dental tissues. Laser application in dentistry requires special training as well as some protective measures. Laser advantages, compared to traditional preparation techniques, involve the absence of vibration, painless preparation, possibility of preparation without anesthetic and easier patient's adjustment to dental intervention which is of importance, especially in pediatric dentistry., Savremena stomatologija teži ka što manjoj traumatizaciji pacijenta prilikom rada uz maksimalni učinak. Savremeni materijali uz nove vidove preparacije kaviteta pružaju mogućnost sanacije karijesnih lezija u najkraćem vremenskom roku. Vidovi preparacije kaviteta su se znatno promenili otkako je uvedeno prvo mašinski napravljeno svrdlo za uklanjanje karijesa. Tehnološki napredak materijala za ispune i načina preparacije doveli su do savremenih karbidnih i dijamantskih svrdla koja se koriste uz obavezno vodeno hlađenje. Inovaciju na polju rotirajućih instrumenata predstavljaju polimerna 'pametna' svrdla, koja uklanjaju karijesnu leziju bez mogućnosti povređivanja i uklanjanja zdrave zubne strukture. Ovo je moguće zahvaljujući čvrstoći koju poseduju, koja je manja od čvrstoće zdravog dentina. Zahvaljujući prirodi materijala od kojih su izrađena, ova svrdla omogućuju bezbolniji rad uz manje vibracija i slabije zagrevanje zubne supstance. Laseri su relativno novo tehnološko sredstvo u stomatologiji, a njihova klinička upotreba počela je osamdesetih godina dvadesetog veka. Laseri funkcionišu po principu ablacije, za šta je neophodno prisustvo vode. Najveći potencijal među ispitivanim laserima pokazali su erbijumski laseri, kojima je moguće uraditi efikasnu ablaciju čvrstih zubnih tkiva. Za korišćenje lasera u stomatologiji neophodni su posebna obuka i odgovarajuće mere zaštite. Prednosti lasera u poređenju sa drugim metodama preparacije čvrstih zubnih tkiva su nepostojanje vibracija, bezbolan rad, mogućnost rada bez anestezije i lakše prilagođavanje pacijenta stomatološkim intervencijama, što je veoma značajno u dečjoj stomatologiji.",
publisher = "Srpsko lekarsko društvo, Beograd",
journal = "Srpski arhiv za celokupno lekarstvo",
title = "Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser, Minimalno invazivna preparacija čvrstih zubnih tkiva savremenim polimernim rotirajućim instrumentima i laserom",
volume = "142",
number = "5-6",
pages = "365-370",
doi = "10.2298/SARH1406365B"
}
Beloica, M., Vulićević, Z., Mandinić, Z., Radović, I., Jovičić, O., Carević, M.,& Tekić, J.. (2014). Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser. in Srpski arhiv za celokupno lekarstvo
Srpsko lekarsko društvo, Beograd., 142(5-6), 365-370.
https://doi.org/10.2298/SARH1406365B
Beloica M, Vulićević Z, Mandinić Z, Radović I, Jovičić O, Carević M, Tekić J. Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser. in Srpski arhiv za celokupno lekarstvo. 2014;142(5-6):365-370.
doi:10.2298/SARH1406365B .
Beloica, Miloš, Vulićević, Zoran, Mandinić, Zoran, Radović, Ivana, Jovičić, Olivera, Carević, Momir, Tekić, Jasmina, "Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser" in Srpski arhiv za celokupno lekarstvo, 142, no. 5-6 (2014):365-370,
https://doi.org/10.2298/SARH1406365B . .
1

Push-out bond strength of an experimental self-adhesive resin cement

Juloski, Jelena; Fadda, Giovanni M.; Radović, Ivana; Chieffi, Nicoletta; Vulićević, Zoran; Aragoneses, Juan M.; Ferrari, Marco

(Wiley-Blackwell, Hoboken, 2013)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Fadda, Giovanni M.
AU  - Radović, Ivana
AU  - Chieffi, Nicoletta
AU  - Vulićević, Zoran
AU  - Aragoneses, Juan M.
AU  - Ferrari, Marco
PY  - 2013
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1842
AB  - The adhesion of fiber posts luted with simplified adhesive systems has been a matter of great interest over the past years. The aim of this study was to assess the post retentive potential of experimental self-adhesive resin cement (EXP) when used alone and in combination with a self-etch adhesive. Fiber posts were placed in endodontically treated teeth and divided into four groups (n = 6) according the luting material, as follows: group 1 (EXP alone); group 2 (EXP used with self-etch adhesive); group 3 (marketed dual-cured cement used with self-etch adhesive); and group 4 (marketed self-adhesive cement). The push-out test was used to assess the retentive strength of fiber posts (expressed in MPa), and specimens were analyzed under a stereomicroscope to determine failure mode. The adhesive interface between the cement and root canal dentin for each group was evaluated using scanning electron microscopy. The post retentive potential of group 1 (EXP) (7.48 +/- 4.35 MPa) was comparable with that of marketed cements from group 4 (6.79 +/- 3.68 MPa) and group 3 (8.77 +/- 4.58 MPa). When EXP was used in combination with self-etch adhesive (group 2), significantly higher push-out bond-strength values were measured (15.87 +/- 4.68 MPa) compared with the other groups.
PB  - Wiley-Blackwell, Hoboken
T2  - European Journal of Oral Sciences
T1  - Push-out bond strength of an experimental self-adhesive resin cement
VL  - 121
IS  - 1
SP  - 50
EP  - 56
DO  - 10.1111/eos.12005
ER  - 
@article{
author = "Juloski, Jelena and Fadda, Giovanni M. and Radović, Ivana and Chieffi, Nicoletta and Vulićević, Zoran and Aragoneses, Juan M. and Ferrari, Marco",
year = "2013",
abstract = "The adhesion of fiber posts luted with simplified adhesive systems has been a matter of great interest over the past years. The aim of this study was to assess the post retentive potential of experimental self-adhesive resin cement (EXP) when used alone and in combination with a self-etch adhesive. Fiber posts were placed in endodontically treated teeth and divided into four groups (n = 6) according the luting material, as follows: group 1 (EXP alone); group 2 (EXP used with self-etch adhesive); group 3 (marketed dual-cured cement used with self-etch adhesive); and group 4 (marketed self-adhesive cement). The push-out test was used to assess the retentive strength of fiber posts (expressed in MPa), and specimens were analyzed under a stereomicroscope to determine failure mode. The adhesive interface between the cement and root canal dentin for each group was evaluated using scanning electron microscopy. The post retentive potential of group 1 (EXP) (7.48 +/- 4.35 MPa) was comparable with that of marketed cements from group 4 (6.79 +/- 3.68 MPa) and group 3 (8.77 +/- 4.58 MPa). When EXP was used in combination with self-etch adhesive (group 2), significantly higher push-out bond-strength values were measured (15.87 +/- 4.68 MPa) compared with the other groups.",
publisher = "Wiley-Blackwell, Hoboken",
journal = "European Journal of Oral Sciences",
title = "Push-out bond strength of an experimental self-adhesive resin cement",
volume = "121",
number = "1",
pages = "50-56",
doi = "10.1111/eos.12005"
}
Juloski, J., Fadda, G. M., Radović, I., Chieffi, N., Vulićević, Z., Aragoneses, J. M.,& Ferrari, M.. (2013). Push-out bond strength of an experimental self-adhesive resin cement. in European Journal of Oral Sciences
Wiley-Blackwell, Hoboken., 121(1), 50-56.
https://doi.org/10.1111/eos.12005
Juloski J, Fadda GM, Radović I, Chieffi N, Vulićević Z, Aragoneses JM, Ferrari M. Push-out bond strength of an experimental self-adhesive resin cement. in European Journal of Oral Sciences. 2013;121(1):50-56.
doi:10.1111/eos.12005 .
Juloski, Jelena, Fadda, Giovanni M., Radović, Ivana, Chieffi, Nicoletta, Vulićević, Zoran, Aragoneses, Juan M., Ferrari, Marco, "Push-out bond strength of an experimental self-adhesive resin cement" in European Journal of Oral Sciences, 121, no. 1 (2013):50-56,
https://doi.org/10.1111/eos.12005 . .
8
7
7

Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites

Juloski, Jelena; Beloica, Miloš; Goracci, Cecilia; Chieffi, Nicoletta; Giovannetti, Agostino; Vichi, Alessandro; Vulićević, Zoran; Ferrari, Marco

(Quintessence Publishing Co Inc, Hanover Park, 2013)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Beloica, Miloš
AU  - Goracci, Cecilia
AU  - Chieffi, Nicoletta
AU  - Giovannetti, Agostino
AU  - Vichi, Alessandro
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2013
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1835
AB  - Purpose: To assess the shear bond strength to unground human enamel (ESBS) and flexural strength (FS) of different reinforcing fibers used in combination with a flowable composite resin. Materials and Methods: For ESBS testing, 90 human molars were selected and randomly divided into 9 groups (n = 10) according to the reinforcing fiber to be tested: 1. RTD Quartz Splint additionally impregnated at chair-side with Quartz Splint Resin (RTD); 2. RTD Quartz Splint without additional impregnation; 3. Ribbond- THM (Ribbond) impregnated with OptiBond FL Adhesive; 4: Ribbond Triaxial (Ribbond) impregnated with OptiBond FL Adhesive; 5. Connect (Kerr) impregnated with OptiBond FL Adhesive; 6. Construct (Kerr) impregnated with OptiBond FL Adhesive; 7. everStick PERIO (Stick Tech); 8. everStick C&B (Stick Tech); 9. nonreinforced composite Premise flowable (Kerr). Cylinders of flowable composite reinforced with the fibers were bonded to the intact buccal surface of the teeth. After 24 h of storage, shear loading was performed until failure occurred. FS was assessed performing three- point bending test according to ISO Standard 4049/2000. ESBS and FS data were analyzed using one- way ANOVA, followed by Tukey's HSD test for post- hoc comparisons (p  lt  0.05). Results: For each group, the ESBS and FS, respectively, in MPa were: 1. 17.07 +/- 4.52 and 472.69 +/- 30.49; 2. 14.98 +/- 3.92 and 441.77 +/- 61.43; 3. 18.59 +/- 5.67 and 186.89 +/- 43.89; 4. 16.74 +/- 6.27 and 314.41 +/- 148.52; 5. 14.38 +/- 4.14 and 223.80 +/- 77.35; 6. 16.00 +/- 5.55 and 287.62 +/- 85.91; 7. 16.42 +/- 3.67 and 285.35 +/- 39.68; 8. 23.24 +/- 5.81 and 370.46 +/- 29.26; 9. 12.58 +/- 4.76 and 87.75 +/- 22.87. For most fibers, no significant difference in ESBS was found compared to the control group, except for everStick C&B, which yielded higher ESBS. Nonreinforced composite exhibited the lowest FS, while all fibers positively affected the FS. Conclusions: Fiber reinforcement of flowable composite does not affect its ESBS. The flexural strength of FRCs is significantly influenced by fiber composition and pattern.
PB  - Quintessence Publishing Co Inc, Hanover Park
T2  - Journal of Adhesive Dentistry
T1  - Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites
VL  - 15
IS  - 2
SP  - 123
EP  - 130
DO  - 10.3290/j.jad.a28362
ER  - 
@article{
author = "Juloski, Jelena and Beloica, Miloš and Goracci, Cecilia and Chieffi, Nicoletta and Giovannetti, Agostino and Vichi, Alessandro and Vulićević, Zoran and Ferrari, Marco",
year = "2013",
abstract = "Purpose: To assess the shear bond strength to unground human enamel (ESBS) and flexural strength (FS) of different reinforcing fibers used in combination with a flowable composite resin. Materials and Methods: For ESBS testing, 90 human molars were selected and randomly divided into 9 groups (n = 10) according to the reinforcing fiber to be tested: 1. RTD Quartz Splint additionally impregnated at chair-side with Quartz Splint Resin (RTD); 2. RTD Quartz Splint without additional impregnation; 3. Ribbond- THM (Ribbond) impregnated with OptiBond FL Adhesive; 4: Ribbond Triaxial (Ribbond) impregnated with OptiBond FL Adhesive; 5. Connect (Kerr) impregnated with OptiBond FL Adhesive; 6. Construct (Kerr) impregnated with OptiBond FL Adhesive; 7. everStick PERIO (Stick Tech); 8. everStick C&B (Stick Tech); 9. nonreinforced composite Premise flowable (Kerr). Cylinders of flowable composite reinforced with the fibers were bonded to the intact buccal surface of the teeth. After 24 h of storage, shear loading was performed until failure occurred. FS was assessed performing three- point bending test according to ISO Standard 4049/2000. ESBS and FS data were analyzed using one- way ANOVA, followed by Tukey's HSD test for post- hoc comparisons (p  lt  0.05). Results: For each group, the ESBS and FS, respectively, in MPa were: 1. 17.07 +/- 4.52 and 472.69 +/- 30.49; 2. 14.98 +/- 3.92 and 441.77 +/- 61.43; 3. 18.59 +/- 5.67 and 186.89 +/- 43.89; 4. 16.74 +/- 6.27 and 314.41 +/- 148.52; 5. 14.38 +/- 4.14 and 223.80 +/- 77.35; 6. 16.00 +/- 5.55 and 287.62 +/- 85.91; 7. 16.42 +/- 3.67 and 285.35 +/- 39.68; 8. 23.24 +/- 5.81 and 370.46 +/- 29.26; 9. 12.58 +/- 4.76 and 87.75 +/- 22.87. For most fibers, no significant difference in ESBS was found compared to the control group, except for everStick C&B, which yielded higher ESBS. Nonreinforced composite exhibited the lowest FS, while all fibers positively affected the FS. Conclusions: Fiber reinforcement of flowable composite does not affect its ESBS. The flexural strength of FRCs is significantly influenced by fiber composition and pattern.",
publisher = "Quintessence Publishing Co Inc, Hanover Park",
journal = "Journal of Adhesive Dentistry",
title = "Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites",
volume = "15",
number = "2",
pages = "123-130",
doi = "10.3290/j.jad.a28362"
}
Juloski, J., Beloica, M., Goracci, C., Chieffi, N., Giovannetti, A., Vichi, A., Vulićević, Z.,& Ferrari, M.. (2013). Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites. in Journal of Adhesive Dentistry
Quintessence Publishing Co Inc, Hanover Park., 15(2), 123-130.
https://doi.org/10.3290/j.jad.a28362
Juloski J, Beloica M, Goracci C, Chieffi N, Giovannetti A, Vichi A, Vulićević Z, Ferrari M. Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites. in Journal of Adhesive Dentistry. 2013;15(2):123-130.
doi:10.3290/j.jad.a28362 .
Juloski, Jelena, Beloica, Miloš, Goracci, Cecilia, Chieffi, Nicoletta, Giovannetti, Agostino, Vichi, Alessandro, Vulićević, Zoran, Ferrari, Marco, "Shear Bond Strength to Enamel and Flexural Strength of Different Fiber-reinforced Composites" in Journal of Adhesive Dentistry, 15, no. 2 (2013):123-130,
https://doi.org/10.3290/j.jad.a28362 . .
10
5
8

Post-retentive ability of new flowable resin composites

Juloski, Jelena; Goracci, Cecilia; Radović, Ivana; Chieffi, Nicoleita; Vichi, Alessandro; Vulićević, Zoran; Ferrari, Marco

(2013)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Goracci, Cecilia
AU  - Radović, Ivana
AU  - Chieffi, Nicoleita
AU  - Vichi, Alessandro
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2013
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1825
AB  - Purpose: To investigate the applicability of flowable composites as post luting agents by assessing the push-out strength of posts. Methods: 36 intact single rooted human premolars were selected. The endodontic treatment was performed and half of the specimens were restored with light transmitting posts (DT Light Post Illusion) and the other half with opaque posts (Tech 21 X-OP). In both groups the following combinations of adhesive/cement were tested: OptiBond Solo Plus/Nexus Third Generation (NX3), XP Bond/SureFil SDR Flow (SDR), and Vertise Flow (VF). Push-out test was used to assess the retentive strength of fiber posts, which was expressed in megapascals (MPa). Specimens were analyzed under a stereomicroscope to determine failure mode (adhesive between luting agent and post, adhesive between luting agent and dentin or mixed failure). Push-out data and failure mode distribution were analyzed by two-way ANOVA and Chi-square test, respectively (P lt  0.05). Results: The statistical analysis revealed that only the type of luting material significantly influenced push-out bond strength of the post (P lt  0.001). SDR (9.00 +/- 2.17 MLPa) performed similarly to the control group NX3 (7.15 +/- 1.74 MPa), while VF (4.81 +/- 1.51 MPa) should significantly lower bond strength. Failure modes differed significantly among groups.
T2  - American Journal of Dentistry
T1  - Post-retentive ability of new flowable resin composites
VL  - 26
IS  - 6
SP  - 324
EP  - 328
UR  - https://hdl.handle.net/21.15107/rcub_smile_1825
ER  - 
@article{
author = "Juloski, Jelena and Goracci, Cecilia and Radović, Ivana and Chieffi, Nicoleita and Vichi, Alessandro and Vulićević, Zoran and Ferrari, Marco",
year = "2013",
abstract = "Purpose: To investigate the applicability of flowable composites as post luting agents by assessing the push-out strength of posts. Methods: 36 intact single rooted human premolars were selected. The endodontic treatment was performed and half of the specimens were restored with light transmitting posts (DT Light Post Illusion) and the other half with opaque posts (Tech 21 X-OP). In both groups the following combinations of adhesive/cement were tested: OptiBond Solo Plus/Nexus Third Generation (NX3), XP Bond/SureFil SDR Flow (SDR), and Vertise Flow (VF). Push-out test was used to assess the retentive strength of fiber posts, which was expressed in megapascals (MPa). Specimens were analyzed under a stereomicroscope to determine failure mode (adhesive between luting agent and post, adhesive between luting agent and dentin or mixed failure). Push-out data and failure mode distribution were analyzed by two-way ANOVA and Chi-square test, respectively (P lt  0.05). Results: The statistical analysis revealed that only the type of luting material significantly influenced push-out bond strength of the post (P lt  0.001). SDR (9.00 +/- 2.17 MLPa) performed similarly to the control group NX3 (7.15 +/- 1.74 MPa), while VF (4.81 +/- 1.51 MPa) should significantly lower bond strength. Failure modes differed significantly among groups.",
journal = "American Journal of Dentistry",
title = "Post-retentive ability of new flowable resin composites",
volume = "26",
number = "6",
pages = "324-328",
url = "https://hdl.handle.net/21.15107/rcub_smile_1825"
}
Juloski, J., Goracci, C., Radović, I., Chieffi, N., Vichi, A., Vulićević, Z.,& Ferrari, M.. (2013). Post-retentive ability of new flowable resin composites. in American Journal of Dentistry, 26(6), 324-328.
https://hdl.handle.net/21.15107/rcub_smile_1825
Juloski J, Goracci C, Radović I, Chieffi N, Vichi A, Vulićević Z, Ferrari M. Post-retentive ability of new flowable resin composites. in American Journal of Dentistry. 2013;26(6):324-328.
https://hdl.handle.net/21.15107/rcub_smile_1825 .
Juloski, Jelena, Goracci, Cecilia, Radović, Ivana, Chieffi, Nicoleita, Vichi, Alessandro, Vulićević, Zoran, Ferrari, Marco, "Post-retentive ability of new flowable resin composites" in American Journal of Dentistry, 26, no. 6 (2013):324-328,
https://hdl.handle.net/21.15107/rcub_smile_1825 .
2
3

Ferrule Effect: A Literature Review

Juloski, Jelena; Radović, Ivana; Goracci, Cecilia; Vulićević, Zoran; Ferrari, Marco

(Elsevier Science Inc, New York, 2012)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Radović, Ivana
AU  - Goracci, Cecilia
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2012
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1695
AB  - Introduction: Preserving intact coronal and radicular tooth structure, especially maintaining cervical tissue to create a ferrule effect, is considered to be crucial for the optimal biomechanical behavior of restored teeth. The ferrule effect has been extensively studied and still remains controversial from many perspectives. The purpose of this study was to summarize the results of research conducted on different issues related to the ferrule effect and published in peer-reviewed journals listed in PubMed. Methods: The search was conducted using the following key words: "ferrule" and "ferrule effect" alone or in combination with "literature review," "fracture resistance," "fatigue," "finite element analysis," and "clinical trials." Results: The findings from reviewed articles were categorized into three main categories: laboratory studies, computer simulation, and clinical trials. Laboratory studies were further classified into subchapters based on the main aspect investigated in relation to the ferrule effect. Conclusions: The presence of a 1.5- to 2-mm ferrule has a positive effect on fracture resistance of endodontically treated teeth. If the clinical situation does not permit a circumferential ferrule, an incomplete ferrule is considered a better option than a complete lack of ferrule. Including a ferrule in preparation design could lead to more favorable fracture patters. Providing an adequate ferrule lowers the impact of the post and core system, luting agents, and the final restoration on tooth performance. In teeth with no coronal structure, in order to provide a ferrule, orthodontic extrusion should be considered rather than surgical crown lengthening. If neither of the alternative methods for providing a ferrule can be performed, available evidence suggests that a poor clinical outcome is very likely. (J Endod 2012;38:11-19)
PB  - Elsevier Science Inc, New York
T2  - Journal of Endodontics
T1  - Ferrule Effect: A Literature Review
VL  - 38
IS  - 1
SP  - 11
EP  - 19
DO  - 10.1016/j.joen.2011.09.024
ER  - 
@article{
author = "Juloski, Jelena and Radović, Ivana and Goracci, Cecilia and Vulićević, Zoran and Ferrari, Marco",
year = "2012",
abstract = "Introduction: Preserving intact coronal and radicular tooth structure, especially maintaining cervical tissue to create a ferrule effect, is considered to be crucial for the optimal biomechanical behavior of restored teeth. The ferrule effect has been extensively studied and still remains controversial from many perspectives. The purpose of this study was to summarize the results of research conducted on different issues related to the ferrule effect and published in peer-reviewed journals listed in PubMed. Methods: The search was conducted using the following key words: "ferrule" and "ferrule effect" alone or in combination with "literature review," "fracture resistance," "fatigue," "finite element analysis," and "clinical trials." Results: The findings from reviewed articles were categorized into three main categories: laboratory studies, computer simulation, and clinical trials. Laboratory studies were further classified into subchapters based on the main aspect investigated in relation to the ferrule effect. Conclusions: The presence of a 1.5- to 2-mm ferrule has a positive effect on fracture resistance of endodontically treated teeth. If the clinical situation does not permit a circumferential ferrule, an incomplete ferrule is considered a better option than a complete lack of ferrule. Including a ferrule in preparation design could lead to more favorable fracture patters. Providing an adequate ferrule lowers the impact of the post and core system, luting agents, and the final restoration on tooth performance. In teeth with no coronal structure, in order to provide a ferrule, orthodontic extrusion should be considered rather than surgical crown lengthening. If neither of the alternative methods for providing a ferrule can be performed, available evidence suggests that a poor clinical outcome is very likely. (J Endod 2012;38:11-19)",
publisher = "Elsevier Science Inc, New York",
journal = "Journal of Endodontics",
title = "Ferrule Effect: A Literature Review",
volume = "38",
number = "1",
pages = "11-19",
doi = "10.1016/j.joen.2011.09.024"
}
Juloski, J., Radović, I., Goracci, C., Vulićević, Z.,& Ferrari, M.. (2012). Ferrule Effect: A Literature Review. in Journal of Endodontics
Elsevier Science Inc, New York., 38(1), 11-19.
https://doi.org/10.1016/j.joen.2011.09.024
Juloski J, Radović I, Goracci C, Vulićević Z, Ferrari M. Ferrule Effect: A Literature Review. in Journal of Endodontics. 2012;38(1):11-19.
doi:10.1016/j.joen.2011.09.024 .
Juloski, Jelena, Radović, Ivana, Goracci, Cecilia, Vulićević, Zoran, Ferrari, Marco, "Ferrule Effect: A Literature Review" in Journal of Endodontics, 38, no. 1 (2012):11-19,
https://doi.org/10.1016/j.joen.2011.09.024 . .
6
204
118
178

Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching

Juloski, Jelena; Goracci, Cecilia; Rengo, Carlo; Giovannetti, Agostino; Vichi, Alessandro; Vulićević, Zoran; Ferrari, Marco

(2012)

TY  - JOUR
AU  - Juloski, Jelena
AU  - Goracci, Cecilia
AU  - Rengo, Carlo
AU  - Giovannetti, Agostino
AU  - Vichi, Alessandro
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2012
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1693
AB  - Purpose: To assess the influence of preliminary phosphoric acid-etching on shear bond strength (SBS) to enamel and dentin of a self-adhering restorative composite and of a new self-etch adhesive used in combination with the proprietary flowable composite. Methods: 100 human molars were selected. SBS was assessed on flat buccal enamel surfaces and mid-coronal dentin. Teeth from each group were divided into five subgroups (n=10): (1) FL: etch-and-rinse adhesive OptiBond FL/Premise flowable; (2) XTR: 2-step self-etch adhesive OptiBond XTR/Premise flowable; (3) eXTR: OptiBond XTR on etched substrates/Premise flowable; (4) VF: self-adhering flowable composite Vertise Flow; (5) eVF: Vertise Flow on etched substrates. Specimens were stressed in shear until failure. Failure modes were evaluated under a stereomicroscope. Data were analyzed by two-way ANOVA and Fisher's exact test (P lt  0.05). Results: Dental substrate, material and between-factor interaction significantly influenced SBS (MPa). In FL group (16.83 +/- 2.93) significantly higher SBS to enamel than in the other groups (XTR 8.59 +/- 4.39; eXTR 7.04 +/- 3.63; VF 6.61 +/- 2,41; eVF 9.87 +/- 4.24) was measured. On dentin FL (8.15 +/- 3.88) performed similarly to XTR (10.60 +/- 5.0), eXTR (9.60 +/- 4.91) and eVF (5.48 +/- 4.94); VF recorded significantly lower SBS (2.94 +/- 2.79 MPa). Failure modes differed significantly among groups. (Am J Dent 2012;25:239-243).
T2  - American Journal of Dentistry
T1  - Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching
VL  - 25
IS  - 4
SP  - 239
EP  - 243
UR  - https://hdl.handle.net/21.15107/rcub_smile_1693
ER  - 
@article{
author = "Juloski, Jelena and Goracci, Cecilia and Rengo, Carlo and Giovannetti, Agostino and Vichi, Alessandro and Vulićević, Zoran and Ferrari, Marco",
year = "2012",
abstract = "Purpose: To assess the influence of preliminary phosphoric acid-etching on shear bond strength (SBS) to enamel and dentin of a self-adhering restorative composite and of a new self-etch adhesive used in combination with the proprietary flowable composite. Methods: 100 human molars were selected. SBS was assessed on flat buccal enamel surfaces and mid-coronal dentin. Teeth from each group were divided into five subgroups (n=10): (1) FL: etch-and-rinse adhesive OptiBond FL/Premise flowable; (2) XTR: 2-step self-etch adhesive OptiBond XTR/Premise flowable; (3) eXTR: OptiBond XTR on etched substrates/Premise flowable; (4) VF: self-adhering flowable composite Vertise Flow; (5) eVF: Vertise Flow on etched substrates. Specimens were stressed in shear until failure. Failure modes were evaluated under a stereomicroscope. Data were analyzed by two-way ANOVA and Fisher's exact test (P lt  0.05). Results: Dental substrate, material and between-factor interaction significantly influenced SBS (MPa). In FL group (16.83 +/- 2.93) significantly higher SBS to enamel than in the other groups (XTR 8.59 +/- 4.39; eXTR 7.04 +/- 3.63; VF 6.61 +/- 2,41; eVF 9.87 +/- 4.24) was measured. On dentin FL (8.15 +/- 3.88) performed similarly to XTR (10.60 +/- 5.0), eXTR (9.60 +/- 4.91) and eVF (5.48 +/- 4.94); VF recorded significantly lower SBS (2.94 +/- 2.79 MPa). Failure modes differed significantly among groups. (Am J Dent 2012;25:239-243).",
journal = "American Journal of Dentistry",
title = "Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching",
volume = "25",
number = "4",
pages = "239-243",
url = "https://hdl.handle.net/21.15107/rcub_smile_1693"
}
Juloski, J., Goracci, C., Rengo, C., Giovannetti, A., Vichi, A., Vulićević, Z.,& Ferrari, M.. (2012). Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching. in American Journal of Dentistry, 25(4), 239-243.
https://hdl.handle.net/21.15107/rcub_smile_1693
Juloski J, Goracci C, Rengo C, Giovannetti A, Vichi A, Vulićević Z, Ferrari M. Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching. in American Journal of Dentistry. 2012;25(4):239-243.
https://hdl.handle.net/21.15107/rcub_smile_1693 .
Juloski, Jelena, Goracci, Cecilia, Rengo, Carlo, Giovannetti, Agostino, Vichi, Alessandro, Vulićević, Zoran, Ferrari, Marco, "Enamel and dentin bond strength of new simplified adhesive materials with and without preliminary phosphoric acid-etching" in American Journal of Dentistry, 25, no. 4 (2012):239-243,
https://hdl.handle.net/21.15107/rcub_smile_1693 .
20
28

Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel

Beloica, Miloš; Goracci, Cecilia; Ramos Carvalho, Carlos Augusto; Radović, Ivana; Margvelashvili, Mariam; Vulićević, Zoran; Ferrari, Marco

(Quintessence Publishing Co Inc, Hanover Park, 2010)

TY  - JOUR
AU  - Beloica, Miloš
AU  - Goracci, Cecilia
AU  - Ramos Carvalho, Carlos Augusto
AU  - Radović, Ivana
AU  - Margvelashvili, Mariam
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2010
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1581
AB  - Purpose To determine the bond strength to unground enamel of all in one adhesives in comparison with an etch and rinse system and to compare the reliability of microtensile and microshear methods in providing such measurements Materials and Methods The bonding procedure was performed on enamel of 64 extracted molars The tested all in one adhesives were Bond Force (Tokuyama), AdheSE One (Ivoclar Vivadent) and Xeno V (Dentsply) Prime&Bond NT (Dentsply) served as control Microtensile specimens were obtained from 4 teeth per group Twelve teeth per group were used for microshear testing Microtensile specimens that failed prior to testing were included in statistical calculations, they were assigned the lowest value measured in the respective group Failure modes were observed under light microscope and classified (cohesive within substrates, adhesive mixed) Statistically significant differences in bond strength were assessed among the adhesives within each testing method and between microshear and microtensile data for each adhesive Failure mode distributions were compared using the chi square test Results All in-one adhesives had similar microshear and microtensile bond strengths In both testing methods, the etch and rinse system achieved the strongest bond For all adhesives significantly higher bond strengths were measured with the microshear test In microtensile testing specimens bonded with the etch and rinse adhesive exhibited a significantly different distribution of failure modes The coefficients of variation were extremely high for microtensile bond strength data, particularly of all in one adhesives Conclusion The adhesive potential to intact enamel of recently introduced all in-one adhesives was inferior to that of an etch and rinse system When testing bond strength to enamel of all in one adhesives, microshear testing may be a more accurate method than microtensile
PB  - Quintessence Publishing Co Inc, Hanover Park
T2  - Journal of Adhesive Dentistry
T1  - Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel
VL  - 12
IS  - 6
SP  - 427
EP  - 433
DO  - 10.3290/j.jad.a18237
ER  - 
@article{
author = "Beloica, Miloš and Goracci, Cecilia and Ramos Carvalho, Carlos Augusto and Radović, Ivana and Margvelashvili, Mariam and Vulićević, Zoran and Ferrari, Marco",
year = "2010",
abstract = "Purpose To determine the bond strength to unground enamel of all in one adhesives in comparison with an etch and rinse system and to compare the reliability of microtensile and microshear methods in providing such measurements Materials and Methods The bonding procedure was performed on enamel of 64 extracted molars The tested all in one adhesives were Bond Force (Tokuyama), AdheSE One (Ivoclar Vivadent) and Xeno V (Dentsply) Prime&Bond NT (Dentsply) served as control Microtensile specimens were obtained from 4 teeth per group Twelve teeth per group were used for microshear testing Microtensile specimens that failed prior to testing were included in statistical calculations, they were assigned the lowest value measured in the respective group Failure modes were observed under light microscope and classified (cohesive within substrates, adhesive mixed) Statistically significant differences in bond strength were assessed among the adhesives within each testing method and between microshear and microtensile data for each adhesive Failure mode distributions were compared using the chi square test Results All in-one adhesives had similar microshear and microtensile bond strengths In both testing methods, the etch and rinse system achieved the strongest bond For all adhesives significantly higher bond strengths were measured with the microshear test In microtensile testing specimens bonded with the etch and rinse adhesive exhibited a significantly different distribution of failure modes The coefficients of variation were extremely high for microtensile bond strength data, particularly of all in one adhesives Conclusion The adhesive potential to intact enamel of recently introduced all in-one adhesives was inferior to that of an etch and rinse system When testing bond strength to enamel of all in one adhesives, microshear testing may be a more accurate method than microtensile",
publisher = "Quintessence Publishing Co Inc, Hanover Park",
journal = "Journal of Adhesive Dentistry",
title = "Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel",
volume = "12",
number = "6",
pages = "427-433",
doi = "10.3290/j.jad.a18237"
}
Beloica, M., Goracci, C., Ramos Carvalho, C. A., Radović, I., Margvelashvili, M., Vulićević, Z.,& Ferrari, M.. (2010). Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel. in Journal of Adhesive Dentistry
Quintessence Publishing Co Inc, Hanover Park., 12(6), 427-433.
https://doi.org/10.3290/j.jad.a18237
Beloica M, Goracci C, Ramos Carvalho CA, Radović I, Margvelashvili M, Vulićević Z, Ferrari M. Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel. in Journal of Adhesive Dentistry. 2010;12(6):427-433.
doi:10.3290/j.jad.a18237 .
Beloica, Miloš, Goracci, Cecilia, Ramos Carvalho, Carlos Augusto, Radović, Ivana, Margvelashvili, Mariam, Vulićević, Zoran, Ferrari, Marco, "Microtensile vs Microshear Bond Strength of All-in-One Adhesives to Unground Enamel" in Journal of Adhesive Dentistry, 12, no. 6 (2010):427-433,
https://doi.org/10.3290/j.jad.a18237 . .
33
24
33

Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement

Radović, Ivana; Corciolani, Gabriele; Magni, Elisa; Krstanović, Goranka; Pavlović, Vladimir; Vulićević, Zoran; Ferrari, Marco

(Elsevier Sci Ltd, Oxford, 2009)

TY  - JOUR
AU  - Radović, Ivana
AU  - Corciolani, Gabriele
AU  - Magni, Elisa
AU  - Krstanović, Goranka
AU  - Pavlović, Vladimir
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2009
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1487
AB  - Objectives. The aim of this study was to investigate the effect of fiber post light transmitting ability to the continuity of resin cement-root dentin (C-RD) and resin cement-fiber post (C-FP) interface, elastic modulus and hardness of a dual-cure resin cement. Methods. Spectrophotometric measurements were applied for the determination of light transmission at coronal, middle and apical level as well as at the apical tip through Tech 21 X-OP (TECH) and DT Light Post (DT). Posts were cemented using dual-cured resin cement (Calibra). Roots were sectioned longitudinally through the post. Epoxy resin replicas were made and used to evaluate C-RD and C-FP interface under SEM. Modulus of elasticity (E) and Vicker's hardness (VH) of the cement layer were assessed. Results. No light transmission was detected through TECH. Light transmission through DT decreased from coronal to apical and rose at the apical tip. TECH presented a significantly lower percentage of continuous C-RD and C-FP interface in comparison to DT. Coronal third of C-RD interface in TECH specimens had a significantly higher percentage of continuity than apical third. No regional differences in continuity of C-RD interface were found in DT specimens. E and VH were significantly lower when TECH was used, and decreased from coronal to apical for both posts. Significance. Cementation of fiber post with no light transmitting ability using a dual-cured resin cement resulted in lower E and VH of the cement layer, and lower percentage of continuous C-RD and C-FP interface in comparison to cementation of light transmitting fiber post.
PB  - Elsevier Sci Ltd, Oxford
T2  - Dental Materials
T1  - Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement
VL  - 25
IS  - 7
SP  - 837
EP  - 844
DO  - 10.1016/j.dental.2009.01.004
ER  - 
@article{
author = "Radović, Ivana and Corciolani, Gabriele and Magni, Elisa and Krstanović, Goranka and Pavlović, Vladimir and Vulićević, Zoran and Ferrari, Marco",
year = "2009",
abstract = "Objectives. The aim of this study was to investigate the effect of fiber post light transmitting ability to the continuity of resin cement-root dentin (C-RD) and resin cement-fiber post (C-FP) interface, elastic modulus and hardness of a dual-cure resin cement. Methods. Spectrophotometric measurements were applied for the determination of light transmission at coronal, middle and apical level as well as at the apical tip through Tech 21 X-OP (TECH) and DT Light Post (DT). Posts were cemented using dual-cured resin cement (Calibra). Roots were sectioned longitudinally through the post. Epoxy resin replicas were made and used to evaluate C-RD and C-FP interface under SEM. Modulus of elasticity (E) and Vicker's hardness (VH) of the cement layer were assessed. Results. No light transmission was detected through TECH. Light transmission through DT decreased from coronal to apical and rose at the apical tip. TECH presented a significantly lower percentage of continuous C-RD and C-FP interface in comparison to DT. Coronal third of C-RD interface in TECH specimens had a significantly higher percentage of continuity than apical third. No regional differences in continuity of C-RD interface were found in DT specimens. E and VH were significantly lower when TECH was used, and decreased from coronal to apical for both posts. Significance. Cementation of fiber post with no light transmitting ability using a dual-cured resin cement resulted in lower E and VH of the cement layer, and lower percentage of continuous C-RD and C-FP interface in comparison to cementation of light transmitting fiber post.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Dental Materials",
title = "Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement",
volume = "25",
number = "7",
pages = "837-844",
doi = "10.1016/j.dental.2009.01.004"
}
Radović, I., Corciolani, G., Magni, E., Krstanović, G., Pavlović, V., Vulićević, Z.,& Ferrari, M.. (2009). Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement. in Dental Materials
Elsevier Sci Ltd, Oxford., 25(7), 837-844.
https://doi.org/10.1016/j.dental.2009.01.004
Radović I, Corciolani G, Magni E, Krstanović G, Pavlović V, Vulićević Z, Ferrari M. Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement. in Dental Materials. 2009;25(7):837-844.
doi:10.1016/j.dental.2009.01.004 .
Radović, Ivana, Corciolani, Gabriele, Magni, Elisa, Krstanović, Goranka, Pavlović, Vladimir, Vulićević, Zoran, Ferrari, Marco, "Light transmission through fiber post: The effect on adhesion, elastic modulus and hardness of dual-cure resin cement" in Dental Materials, 25, no. 7 (2009):837-844,
https://doi.org/10.1016/j.dental.2009.01.004 . .
57
45
52

Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface

Radović, Ivana; Monticelli, Francesca; Cury, Alvaro Hafiz; Bertelli, Egidio; Vulićević, Zoran; Ferrari, Marco

(2008)

TY  - JOUR
AU  - Radović, Ivana
AU  - Monticelli, Francesca
AU  - Cury, Alvaro Hafiz
AU  - Bertelli, Egidio
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2008
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1443
AB  - Purpose: To evaluate the influence of surface treatments on microtensile bond strength of luting resin cements to fiber posts. Materials and Methods: Forty-two quartz fiber posts (Light Post, RTD) were divided into 7 groups (n = 6) according to the surface treatment. I and 11: experimental patented industrial treatment consisting of zirconium oxide coating and silanization (RTD); III: industrial treatment followed by adhesive application (XPBond, Dentsply Caulk); IV: adhesive (XPBond); V: adhesive (Prime&Bond NT, Dentsply Caulk); VI: silane (Calibra Silane, Dentsply Caulk); VII: no treatment. Adhesives were used in the self-curing mode. Two cements (Sealbond, RTD - group 1, and Calibra, Dentsply Caulk - groups 11 to VII) were applied on the posts to produce cylindrical specimens. Post/cement interfaces were evaluated under SEM. The surface of the industrially coated posts was examined using energy dispersive analysis by x-ray. Cylinders were cut to obtain microtensile sticks that were loaded in tension at a crosshead speed of 0.5 mm/min until failure. Statistical analysis was performed using Kruskal-Wallis analysis of variance followed by Dunn's multiple range test for post-hoc comparisons (p  lt  0.05). Weibull analysis was also performed. Results: The post/cement bond strength was significantly higher on fiber posts treated industrially (I: 23.14 +/- 8.05 MPa; II: 21.56 +/- 7.07 MPa; III: 22.37 +/- 7.00 MPa) or treated with XPBond adhesive (IV: 21.03 +/- 5.34 MPa) when compared to Prime&Bond NT application (V: 14.05 +/- 5.06 MPa), silanization (VI: 6.31 +/- 4.60 MPa) or no treatment (VII: 4.62 +/- 4.31) of conventional fiber posts (p  lt  0.001). Conclusion: The experimental industrial surface treatment and the adhesive application enhanced fiber post to resin cement interfacial strength. Industrial pretreatment may simplify the clinical luting procedure.
T2  - Journal of Adhesive Dentistry
T1  - Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface
VL  - 10
IS  - 1
SP  - 57
EP  - 66
UR  - https://hdl.handle.net/21.15107/rcub_smile_1443
ER  - 
@article{
author = "Radović, Ivana and Monticelli, Francesca and Cury, Alvaro Hafiz and Bertelli, Egidio and Vulićević, Zoran and Ferrari, Marco",
year = "2008",
abstract = "Purpose: To evaluate the influence of surface treatments on microtensile bond strength of luting resin cements to fiber posts. Materials and Methods: Forty-two quartz fiber posts (Light Post, RTD) were divided into 7 groups (n = 6) according to the surface treatment. I and 11: experimental patented industrial treatment consisting of zirconium oxide coating and silanization (RTD); III: industrial treatment followed by adhesive application (XPBond, Dentsply Caulk); IV: adhesive (XPBond); V: adhesive (Prime&Bond NT, Dentsply Caulk); VI: silane (Calibra Silane, Dentsply Caulk); VII: no treatment. Adhesives were used in the self-curing mode. Two cements (Sealbond, RTD - group 1, and Calibra, Dentsply Caulk - groups 11 to VII) were applied on the posts to produce cylindrical specimens. Post/cement interfaces were evaluated under SEM. The surface of the industrially coated posts was examined using energy dispersive analysis by x-ray. Cylinders were cut to obtain microtensile sticks that were loaded in tension at a crosshead speed of 0.5 mm/min until failure. Statistical analysis was performed using Kruskal-Wallis analysis of variance followed by Dunn's multiple range test for post-hoc comparisons (p  lt  0.05). Weibull analysis was also performed. Results: The post/cement bond strength was significantly higher on fiber posts treated industrially (I: 23.14 +/- 8.05 MPa; II: 21.56 +/- 7.07 MPa; III: 22.37 +/- 7.00 MPa) or treated with XPBond adhesive (IV: 21.03 +/- 5.34 MPa) when compared to Prime&Bond NT application (V: 14.05 +/- 5.06 MPa), silanization (VI: 6.31 +/- 4.60 MPa) or no treatment (VII: 4.62 +/- 4.31) of conventional fiber posts (p  lt  0.001). Conclusion: The experimental industrial surface treatment and the adhesive application enhanced fiber post to resin cement interfacial strength. Industrial pretreatment may simplify the clinical luting procedure.",
journal = "Journal of Adhesive Dentistry",
title = "Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface",
volume = "10",
number = "1",
pages = "57-66",
url = "https://hdl.handle.net/21.15107/rcub_smile_1443"
}
Radović, I., Monticelli, F., Cury, A. H., Bertelli, E., Vulićević, Z.,& Ferrari, M.. (2008). Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface. in Journal of Adhesive Dentistry, 10(1), 57-66.
https://hdl.handle.net/21.15107/rcub_smile_1443
Radović I, Monticelli F, Cury AH, Bertelli E, Vulićević Z, Ferrari M. Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface. in Journal of Adhesive Dentistry. 2008;10(1):57-66.
https://hdl.handle.net/21.15107/rcub_smile_1443 .
Radović, Ivana, Monticelli, Francesca, Cury, Alvaro Hafiz, Bertelli, Egidio, Vulićević, Zoran, Ferrari, Marco, "Coupling of composite resin cements to quartz fiber posts: A comparison of industrial and 'chairside' treatments of the post surface" in Journal of Adhesive Dentistry, 10, no. 1 (2008):57-66,
https://hdl.handle.net/21.15107/rcub_smile_1443 .
8
8

Microtensile bond strength of self-etching adhesives to dentin

Vulićević, Zoran; Radović, Ivana; Krstanović, Goranka; Mandić, Jelena; Cury, Alvaro Hafiz; Ferrari, Marco

(Savez inženjera metalurgije Srbije, Beograd, 2008)

TY  - JOUR
AU  - Vulićević, Zoran
AU  - Radović, Ivana
AU  - Krstanović, Goranka
AU  - Mandić, Jelena
AU  - Cury, Alvaro Hafiz
AU  - Ferrari, Marco
PY  - 2008
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1404
AB  - The aim of this study was to determine micro tensile bond strength of two and one-step self-etching adhesive systems to dentin. 25 intact human third molars were used. Flat surfaces of mid-coronal dentin were exposed and the teeth were divided into 5 groups (n=5). Composite build-ups were made using the following self-etching systems / composite materials: 2-step self-etching system Contax / Ecusphere Carat (DMG), 2-step self-etching system AdheSE / Tetric Ceram (Ivoclar Vivadent), 1-step 2-components self etching system Futurabond NR / Grandio (Voco) and 1-step 1-component self-etching adhesive G Bond / Gradia Direct (GC Corp.). Two-step etch-and-rinse system PQ Clear with Amelogen Universal composite resin (Ultra dent) was used in the control group. Bond strength was assessed with the non-trimming micro tensile technique. Statistical analysis was performed using the 1-way ANOVA, followed by the Tukey test for post-hoc comparisons (p lt 0.05). Investigated self-etching systems showed satisfactory values of micro tensile bond strength to dentin after 24 hours. Two-step self-etching system AdheSE resulted in significantly higher bond strength than all the other groups (p lt 0.001). Micro tensile bond strength of self-etching systems Contax, Futurabond NR and G Bond was comparable to the etch-and-rinse system PQ Clear. .
AB  - Cilj rada bio je da se odredi jačina veze dvofaznih i jednofaznih samonagrizajućih adhezivnih sistema sa dentinom. Površine dentina su eksponirane na 25 intaktnih trećih molara i zubi su podeljeni u 5 grupa (n=5). Izrađene su kompozitne nadogradnje korišćenjem sledećih samonagrizajućih adheziva / kompozitnih materijala: dvofazni samonagrizajući sistem Contax / Ecusphere Carat (DMG), dvofazni samonagrizajući sistem AdheSE / Tetric Ceram (Ivoclar Vivadent), jednofazni dvokomponentni samonagrizajući sistem Futurabond NR / Grandio (Voco) i jednofazni jednokomponentni samonagrizajući sistem G Bond / Gradia Direct (GC Corp.). Dvofazni adhezivni sistem sa potpunim nagrizanjem PQ Clear sa Amelogen Universal kompozitnim materijalom (Ultradent) korišćen je u kontrolnoj grupi. Jačina veze određena je testom otpornosti mikrouzoraka na kidanje. Rezultati su statistički analizirani jednofaktorskom analizom varijanse (ANOVA) i Tukey testom (p lt 0.05). Ispitivani samonagrizajući sistemi pokazali su zadovoljavajuće vrednosti jačine veze sa dentinom nakon 24 časa. Jačina veze dvofaznog samonagrizajućeg sistema AdheSE bila je značajno viša nego jačina veze u ostalim grupama (p lt 0.001). Jačine veze samonagrizajućih sistema Contax, Futurabond NR i G Bond nisu se statistički značajno razlikovale od jačine veze sistema sa potpunim nagrizanjem PQ Clear. .
PB  - Savez inženjera metalurgije Srbije, Beograd
T2  - Metalurgija
T1  - Microtensile bond strength of self-etching adhesives to dentin
VL  - 14
IS  - 2
SP  - 101
EP  - 109
UR  - https://hdl.handle.net/21.15107/rcub_smile_1404
ER  - 
@article{
author = "Vulićević, Zoran and Radović, Ivana and Krstanović, Goranka and Mandić, Jelena and Cury, Alvaro Hafiz and Ferrari, Marco",
year = "2008",
abstract = "The aim of this study was to determine micro tensile bond strength of two and one-step self-etching adhesive systems to dentin. 25 intact human third molars were used. Flat surfaces of mid-coronal dentin were exposed and the teeth were divided into 5 groups (n=5). Composite build-ups were made using the following self-etching systems / composite materials: 2-step self-etching system Contax / Ecusphere Carat (DMG), 2-step self-etching system AdheSE / Tetric Ceram (Ivoclar Vivadent), 1-step 2-components self etching system Futurabond NR / Grandio (Voco) and 1-step 1-component self-etching adhesive G Bond / Gradia Direct (GC Corp.). Two-step etch-and-rinse system PQ Clear with Amelogen Universal composite resin (Ultra dent) was used in the control group. Bond strength was assessed with the non-trimming micro tensile technique. Statistical analysis was performed using the 1-way ANOVA, followed by the Tukey test for post-hoc comparisons (p lt 0.05). Investigated self-etching systems showed satisfactory values of micro tensile bond strength to dentin after 24 hours. Two-step self-etching system AdheSE resulted in significantly higher bond strength than all the other groups (p lt 0.001). Micro tensile bond strength of self-etching systems Contax, Futurabond NR and G Bond was comparable to the etch-and-rinse system PQ Clear. ., Cilj rada bio je da se odredi jačina veze dvofaznih i jednofaznih samonagrizajućih adhezivnih sistema sa dentinom. Površine dentina su eksponirane na 25 intaktnih trećih molara i zubi su podeljeni u 5 grupa (n=5). Izrađene su kompozitne nadogradnje korišćenjem sledećih samonagrizajućih adheziva / kompozitnih materijala: dvofazni samonagrizajući sistem Contax / Ecusphere Carat (DMG), dvofazni samonagrizajući sistem AdheSE / Tetric Ceram (Ivoclar Vivadent), jednofazni dvokomponentni samonagrizajući sistem Futurabond NR / Grandio (Voco) i jednofazni jednokomponentni samonagrizajući sistem G Bond / Gradia Direct (GC Corp.). Dvofazni adhezivni sistem sa potpunim nagrizanjem PQ Clear sa Amelogen Universal kompozitnim materijalom (Ultradent) korišćen je u kontrolnoj grupi. Jačina veze određena je testom otpornosti mikrouzoraka na kidanje. Rezultati su statistički analizirani jednofaktorskom analizom varijanse (ANOVA) i Tukey testom (p lt 0.05). Ispitivani samonagrizajući sistemi pokazali su zadovoljavajuće vrednosti jačine veze sa dentinom nakon 24 časa. Jačina veze dvofaznog samonagrizajućeg sistema AdheSE bila je značajno viša nego jačina veze u ostalim grupama (p lt 0.001). Jačine veze samonagrizajućih sistema Contax, Futurabond NR i G Bond nisu se statistički značajno razlikovale od jačine veze sistema sa potpunim nagrizanjem PQ Clear. .",
publisher = "Savez inženjera metalurgije Srbije, Beograd",
journal = "Metalurgija",
title = "Microtensile bond strength of self-etching adhesives to dentin",
volume = "14",
number = "2",
pages = "101-109",
url = "https://hdl.handle.net/21.15107/rcub_smile_1404"
}
Vulićević, Z., Radović, I., Krstanović, G., Mandić, J., Cury, A. H.,& Ferrari, M.. (2008). Microtensile bond strength of self-etching adhesives to dentin. in Metalurgija
Savez inženjera metalurgije Srbije, Beograd., 14(2), 101-109.
https://hdl.handle.net/21.15107/rcub_smile_1404
Vulićević Z, Radović I, Krstanović G, Mandić J, Cury AH, Ferrari M. Microtensile bond strength of self-etching adhesives to dentin. in Metalurgija. 2008;14(2):101-109.
https://hdl.handle.net/21.15107/rcub_smile_1404 .
Vulićević, Zoran, Radović, Ivana, Krstanović, Goranka, Mandić, Jelena, Cury, Alvaro Hafiz, Ferrari, Marco, "Microtensile bond strength of self-etching adhesives to dentin" in Metalurgija, 14, no. 2 (2008):101-109,
https://hdl.handle.net/21.15107/rcub_smile_1404 .

Self-adhesive resin cements: A literature review

Radović, Ivana; Monticelli, Francesca; Goracci, Cecilia; Vulićević, Zoran; Ferrari, Marco

(2008)

TY  - JOUR
AU  - Radović, Ivana
AU  - Monticelli, Francesca
AU  - Goracci, Cecilia
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2008
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1391
AB  - Purpose: To summarize research conducted on self-adhesive cements and provide information on their properties, based on the results of original scientific full-length papers from peer-reviewed journals listed in PubMed. Materials and Methods: The search was conducted using the term "self-adhesive cement OR (trade names of currently available products)". Results: Only in vitro studies that investigated two commercially available self-adhesive cements have been published so far. The results were summarized into the following categories: adhesion to tooth substrates (enamel, dentin, root dentin), adhesion to restorative materials (endodontic posts, ceramics, titanium abutments), marginal adaptation, microleakage, mechanical properties, biocompatibility, chemical adhesion and fluoride release, and ratings in clinical use. Conclusion: The majority of available literature data is based on studies that investigated one of the self-adhesive cements that are currently available to clinicians. According to the in vitro results, self-adhesive cement adhesion to dentin and various restorative materials is satisfactory and comparable to other multistep resin cements, while adhesion to enamel appears to be a weak link in their bonding properties. Long-term clinical performance of these materials needs to be assessed prior to making a general recommendation for their use.
T2  - Journal of Adhesive Dentistry
T1  - Self-adhesive resin cements: A literature review
VL  - 10
IS  - 4
SP  - 251
EP  - 258
UR  - https://hdl.handle.net/21.15107/rcub_smile_1391
ER  - 
@article{
author = "Radović, Ivana and Monticelli, Francesca and Goracci, Cecilia and Vulićević, Zoran and Ferrari, Marco",
year = "2008",
abstract = "Purpose: To summarize research conducted on self-adhesive cements and provide information on their properties, based on the results of original scientific full-length papers from peer-reviewed journals listed in PubMed. Materials and Methods: The search was conducted using the term "self-adhesive cement OR (trade names of currently available products)". Results: Only in vitro studies that investigated two commercially available self-adhesive cements have been published so far. The results were summarized into the following categories: adhesion to tooth substrates (enamel, dentin, root dentin), adhesion to restorative materials (endodontic posts, ceramics, titanium abutments), marginal adaptation, microleakage, mechanical properties, biocompatibility, chemical adhesion and fluoride release, and ratings in clinical use. Conclusion: The majority of available literature data is based on studies that investigated one of the self-adhesive cements that are currently available to clinicians. According to the in vitro results, self-adhesive cement adhesion to dentin and various restorative materials is satisfactory and comparable to other multistep resin cements, while adhesion to enamel appears to be a weak link in their bonding properties. Long-term clinical performance of these materials needs to be assessed prior to making a general recommendation for their use.",
journal = "Journal of Adhesive Dentistry",
title = "Self-adhesive resin cements: A literature review",
volume = "10",
number = "4",
pages = "251-258",
url = "https://hdl.handle.net/21.15107/rcub_smile_1391"
}
Radović, I., Monticelli, F., Goracci, C., Vulićević, Z.,& Ferrari, M.. (2008). Self-adhesive resin cements: A literature review. in Journal of Adhesive Dentistry, 10(4), 251-258.
https://hdl.handle.net/21.15107/rcub_smile_1391
Radović I, Monticelli F, Goracci C, Vulićević Z, Ferrari M. Self-adhesive resin cements: A literature review. in Journal of Adhesive Dentistry. 2008;10(4):251-258.
https://hdl.handle.net/21.15107/rcub_smile_1391 .
Radović, Ivana, Monticelli, Francesca, Goracci, Cecilia, Vulićević, Zoran, Ferrari, Marco, "Self-adhesive resin cements: A literature review" in Journal of Adhesive Dentistry, 10, no. 4 (2008):251-258,
https://hdl.handle.net/21.15107/rcub_smile_1391 .
287
374

The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation

Radović, Ivana; Monticelli, Francesca; Goracci, Cecilia; Cury, Alvaro Hafiz; Coniglio, Ivanovic; Vulićević, Zoran; Garcia-Godoy, Franklin; Ferrari, Marco

(Elsevier Sci Ltd, Oxford, 2007)

TY  - JOUR
AU  - Radović, Ivana
AU  - Monticelli, Francesca
AU  - Goracci, Cecilia
AU  - Cury, Alvaro Hafiz
AU  - Coniglio, Ivanovic
AU  - Vulićević, Zoran
AU  - Garcia-Godoy, Franklin
AU  - Ferrari, Marco
PY  - 2007
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1345
AB  - Objectives: To evaluate the influence of different surface treatments on the microtensile bond strength of a dual-cured resin composite to fiber posts. Methods: Thirty-two glass methacrylate-based fiber posts (GC Corp.) were used in the study. Posts were divided into two groups, according to the surface pretreatment performed. Group 1: sandblasting (Rocatec-Pre, 3 M ESPE). Group 2: no pretreatment. In each of the two groups posts received three types of additional "chair-side" treatments. (1) Silane application (Monobond S, Ivoclar Vivadent); (2) adhesive application (Unifil Core self-etching bond, GC); (3) no treatment was performed. A dual-cured resin composite (Unifil Core, GC) was applied on the posts to produce cylindrical specimens. Specimens were cut to obtain microtensile sticks that were loaded in tension at a cross-head speed of 0.5 mm/min until failure. The morphology of the post/composite interface and the post surface morphology were evaluated under SEM. Statistical analysis was performed with two-way ANOVA and Tukey test for post hoc comparisons (p  lt  0.05). Results: Post surface pretreatment did not prove to be a significant factor in post-composite bond strength (p = 0.08), whereas "chair-side" treatment modalities and the interaction between pretreatment and treatment showed a significant influence on bond strength (p  lt  0.001). When no "chair-side" treatment was performed, bond strength was significantly higher on sandblasted posts. Additional adhesive application resulted in significantly lower bond strength on sandblasted posts. When no pretreatment was performed, silane application resulted in higher bond strength than adhesive application. Conclusions: Sandblasting may give an increase in microtensile strength to methacrylate-based glass fiber posts, eliminating the need for additional "chair-side" treatments. Reducing the number of clinical steps could contribute to simplify the clinical procedures.
PB  - Elsevier Sci Ltd, Oxford
T2  - Journal of Dentistry
T1  - The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation
VL  - 35
IS  - 6
SP  - 496
EP  - 502
DO  - 10.1016/j.jdent.2007.01.009
ER  - 
@article{
author = "Radović, Ivana and Monticelli, Francesca and Goracci, Cecilia and Cury, Alvaro Hafiz and Coniglio, Ivanovic and Vulićević, Zoran and Garcia-Godoy, Franklin and Ferrari, Marco",
year = "2007",
abstract = "Objectives: To evaluate the influence of different surface treatments on the microtensile bond strength of a dual-cured resin composite to fiber posts. Methods: Thirty-two glass methacrylate-based fiber posts (GC Corp.) were used in the study. Posts were divided into two groups, according to the surface pretreatment performed. Group 1: sandblasting (Rocatec-Pre, 3 M ESPE). Group 2: no pretreatment. In each of the two groups posts received three types of additional "chair-side" treatments. (1) Silane application (Monobond S, Ivoclar Vivadent); (2) adhesive application (Unifil Core self-etching bond, GC); (3) no treatment was performed. A dual-cured resin composite (Unifil Core, GC) was applied on the posts to produce cylindrical specimens. Specimens were cut to obtain microtensile sticks that were loaded in tension at a cross-head speed of 0.5 mm/min until failure. The morphology of the post/composite interface and the post surface morphology were evaluated under SEM. Statistical analysis was performed with two-way ANOVA and Tukey test for post hoc comparisons (p  lt  0.05). Results: Post surface pretreatment did not prove to be a significant factor in post-composite bond strength (p = 0.08), whereas "chair-side" treatment modalities and the interaction between pretreatment and treatment showed a significant influence on bond strength (p  lt  0.001). When no "chair-side" treatment was performed, bond strength was significantly higher on sandblasted posts. Additional adhesive application resulted in significantly lower bond strength on sandblasted posts. When no pretreatment was performed, silane application resulted in higher bond strength than adhesive application. Conclusions: Sandblasting may give an increase in microtensile strength to methacrylate-based glass fiber posts, eliminating the need for additional "chair-side" treatments. Reducing the number of clinical steps could contribute to simplify the clinical procedures.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Journal of Dentistry",
title = "The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation",
volume = "35",
number = "6",
pages = "496-502",
doi = "10.1016/j.jdent.2007.01.009"
}
Radović, I., Monticelli, F., Goracci, C., Cury, A. H., Coniglio, I., Vulićević, Z., Garcia-Godoy, F.,& Ferrari, M.. (2007). The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation. in Journal of Dentistry
Elsevier Sci Ltd, Oxford., 35(6), 496-502.
https://doi.org/10.1016/j.jdent.2007.01.009
Radović I, Monticelli F, Goracci C, Cury AH, Coniglio I, Vulićević Z, Garcia-Godoy F, Ferrari M. The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation. in Journal of Dentistry. 2007;35(6):496-502.
doi:10.1016/j.jdent.2007.01.009 .
Radović, Ivana, Monticelli, Francesca, Goracci, Cecilia, Cury, Alvaro Hafiz, Coniglio, Ivanovic, Vulićević, Zoran, Garcia-Godoy, Franklin, Ferrari, Marco, "The effect of sandblasting on adhesion of a dual-cured resin composite to methacrylic fiber posts: Microtensile bond strength and SEM evaluation" in Journal of Dentistry, 35, no. 6 (2007):496-502,
https://doi.org/10.1016/j.jdent.2007.01.009 . .
60
52
62

Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach

Radović, Ivana; Monticelli, Francesca; Papacchini, Federica; Magni, Elisa; Cury, Alvaro Hafiz; Vulićević, Zoran; Ferrari, Marco

(Elsevier Sci Ltd, Oxford, 2007)

TY  - JOUR
AU  - Radović, Ivana
AU  - Monticelli, Francesca
AU  - Papacchini, Federica
AU  - Magni, Elisa
AU  - Cury, Alvaro Hafiz
AU  - Vulićević, Zoran
AU  - Ferrari, Marco
PY  - 2007
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1335
AB  - Objectives: Although fiber posts luted in root canals are not directly exposed to oral fluids, water storage is considered as in vitro accelerated aging test for bonded interfaces. The aim of the study was to evaluate the influence of accelerated water aging on fiber post-resin composite adhesion. Methods: Forty fiber posts (DT Light Post, RTD) were randomly divided into two main groups, according to the surface treatment performed. Group 1: XPBond adhesive (Dentsply Caulk); Group II: sandblasting (Rocatec-Pre, 3M ESPE) and XPBond. Dual-cured resin cement (Calibra, Dentsply Caulk) and flowable composite (X-Flow, Dentsply Caulk) were applied on the posts to produce cylindrical specimens. The bond strength at the interface between post and cement/composite was measured with the microtensile test according to the non-trimming technique. Half of the sticks were tested immediately for bond strength, while in the other half testing was performed after 1 month of water storage at 37 degrees C. Post-cement/composite interfaces were evaluated under SEM prior and after water aging. Statistical analysis was performed using the Kruskal-Wallis ANOVA followed by Dunn's multiple range test (P  lt  0.05). Results: Immediate bond strength was higher on sandblasted posts. After water aging the two post surface treatments resulted comparable in bond strength. Resin cement achieved higher bond strength to fiber posts than flowable composite. Water aging significantly reduced bond strength. Conclusions: Sandblasting followed by adhesive coating may improve immediate post-resin bond strength in comparison to adhesive alone. However, fiber post-resin bond strength mediated by hydrophilic adhesive tends to decrease after water aging.
PB  - Elsevier Sci Ltd, Oxford
T2  - Journal of Dentistry
T1  - Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach
VL  - 35
IS  - 8
SP  - 683
EP  - 689
DO  - 10.1016/j.jdent.2007.05.006
ER  - 
@article{
author = "Radović, Ivana and Monticelli, Francesca and Papacchini, Federica and Magni, Elisa and Cury, Alvaro Hafiz and Vulićević, Zoran and Ferrari, Marco",
year = "2007",
abstract = "Objectives: Although fiber posts luted in root canals are not directly exposed to oral fluids, water storage is considered as in vitro accelerated aging test for bonded interfaces. The aim of the study was to evaluate the influence of accelerated water aging on fiber post-resin composite adhesion. Methods: Forty fiber posts (DT Light Post, RTD) were randomly divided into two main groups, according to the surface treatment performed. Group 1: XPBond adhesive (Dentsply Caulk); Group II: sandblasting (Rocatec-Pre, 3M ESPE) and XPBond. Dual-cured resin cement (Calibra, Dentsply Caulk) and flowable composite (X-Flow, Dentsply Caulk) were applied on the posts to produce cylindrical specimens. The bond strength at the interface between post and cement/composite was measured with the microtensile test according to the non-trimming technique. Half of the sticks were tested immediately for bond strength, while in the other half testing was performed after 1 month of water storage at 37 degrees C. Post-cement/composite interfaces were evaluated under SEM prior and after water aging. Statistical analysis was performed using the Kruskal-Wallis ANOVA followed by Dunn's multiple range test (P  lt  0.05). Results: Immediate bond strength was higher on sandblasted posts. After water aging the two post surface treatments resulted comparable in bond strength. Resin cement achieved higher bond strength to fiber posts than flowable composite. Water aging significantly reduced bond strength. Conclusions: Sandblasting followed by adhesive coating may improve immediate post-resin bond strength in comparison to adhesive alone. However, fiber post-resin bond strength mediated by hydrophilic adhesive tends to decrease after water aging.",
publisher = "Elsevier Sci Ltd, Oxford",
journal = "Journal of Dentistry",
title = "Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach",
volume = "35",
number = "8",
pages = "683-689",
doi = "10.1016/j.jdent.2007.05.006"
}
Radović, I., Monticelli, F., Papacchini, F., Magni, E., Cury, A. H., Vulićević, Z.,& Ferrari, M.. (2007). Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach. in Journal of Dentistry
Elsevier Sci Ltd, Oxford., 35(8), 683-689.
https://doi.org/10.1016/j.jdent.2007.05.006
Radović I, Monticelli F, Papacchini F, Magni E, Cury AH, Vulićević Z, Ferrari M. Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach. in Journal of Dentistry. 2007;35(8):683-689.
doi:10.1016/j.jdent.2007.05.006 .
Radović, Ivana, Monticelli, Francesca, Papacchini, Federica, Magni, Elisa, Cury, Alvaro Hafiz, Vulićević, Zoran, Ferrari, Marco, "Accelerated aging of adhesive-mediated fiber post-resin composite bonds: A modeling approach" in Journal of Dentistry, 35, no. 8 (2007):683-689,
https://doi.org/10.1016/j.jdent.2007.05.006 . .
12
10
15

Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin

Radović, I.; Vulićević, Zoran; Garcia-Godoy, Franklin

(Operative Dentistry Inc, Indianapolis, 2006)

TY  - JOUR
AU  - Radović, I.
AU  - Vulićević, Zoran
AU  - Garcia-Godoy, Franklin
PY  - 2006
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1317
AB  - This in vitro study evaluated the resin-dentin interface formed by two 2-step and two 1-step self-etching adhesive systems under SEM. Class V cavities (4 x 2.5 x 1.5 mm) were prepared on the buccal surfaces of 25 extracted intact human third molars using a carbide bur in a high-speed handpiece. Four self-etching systems with corresponding resins were used: two 2-step systems, AdheSE (Ivoclar Vivadent) and Contax (DMG Hamburg), one 1-step/2 components system Futurabond NR (Voco) and a 1-step/1 component adhesive G-Bond (GC Corp). An etch and rinse system, PQ Clear (Ultradent), was used as a control. The teeth were thermocycled (500 cycles, 5 degrees/55 degrees C, 30 seconds dwell time), and 2 sections were made longitudinally through the restorations with a low-speed diamond saw, producing approximately 1-mm wide samples. The samples were polished with silicon carbide paper of increasing grit (400-1000), demineralized (6N HCl, 30 seconds), deproteinized (2.5% NaOCl, 10 minutes), left to air dry for 24 hours in a desiccator under low vacuum pressure, gold sputtered and viewed under SEM (JEOL-JSM-646OLV). In the AdheSE, Contax and Futurabond NR specimens, resin tag penetration into the tubules and lateral tags could be seen. G-Bond showed different interface morphology, with a tight, thin continuous junction and almost no resin penetration into tubules. PQ Clear samples exhibited the highest number of resin tags with numerous lateral tags. A clearly defined hybrid layer was seen in the Contax and PQ Clear specimens. Investigated self-etching systems showed similar interfacial morphology with dentin, except for the 1 step/1 component adhesive G-Bond. The degree of demineralization and interaction with dentin correlated with the acidity of the self-etching primers/adhesives. Fewer resin tags were formed with self-etching primers/adhesives than with the etch and rinse system.
PB  - Operative Dentistry Inc, Indianapolis
T2  - Operative Dentistry
T1  - Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin
VL  - 31
IS  - 6
SP  - 710
EP  - 718
DO  - 10.2341/05-145
ER  - 
@article{
author = "Radović, I. and Vulićević, Zoran and Garcia-Godoy, Franklin",
year = "2006",
abstract = "This in vitro study evaluated the resin-dentin interface formed by two 2-step and two 1-step self-etching adhesive systems under SEM. Class V cavities (4 x 2.5 x 1.5 mm) were prepared on the buccal surfaces of 25 extracted intact human third molars using a carbide bur in a high-speed handpiece. Four self-etching systems with corresponding resins were used: two 2-step systems, AdheSE (Ivoclar Vivadent) and Contax (DMG Hamburg), one 1-step/2 components system Futurabond NR (Voco) and a 1-step/1 component adhesive G-Bond (GC Corp). An etch and rinse system, PQ Clear (Ultradent), was used as a control. The teeth were thermocycled (500 cycles, 5 degrees/55 degrees C, 30 seconds dwell time), and 2 sections were made longitudinally through the restorations with a low-speed diamond saw, producing approximately 1-mm wide samples. The samples were polished with silicon carbide paper of increasing grit (400-1000), demineralized (6N HCl, 30 seconds), deproteinized (2.5% NaOCl, 10 minutes), left to air dry for 24 hours in a desiccator under low vacuum pressure, gold sputtered and viewed under SEM (JEOL-JSM-646OLV). In the AdheSE, Contax and Futurabond NR specimens, resin tag penetration into the tubules and lateral tags could be seen. G-Bond showed different interface morphology, with a tight, thin continuous junction and almost no resin penetration into tubules. PQ Clear samples exhibited the highest number of resin tags with numerous lateral tags. A clearly defined hybrid layer was seen in the Contax and PQ Clear specimens. Investigated self-etching systems showed similar interfacial morphology with dentin, except for the 1 step/1 component adhesive G-Bond. The degree of demineralization and interaction with dentin correlated with the acidity of the self-etching primers/adhesives. Fewer resin tags were formed with self-etching primers/adhesives than with the etch and rinse system.",
publisher = "Operative Dentistry Inc, Indianapolis",
journal = "Operative Dentistry",
title = "Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin",
volume = "31",
number = "6",
pages = "710-718",
doi = "10.2341/05-145"
}
Radović, I., Vulićević, Z.,& Garcia-Godoy, F.. (2006). Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin. in Operative Dentistry
Operative Dentistry Inc, Indianapolis., 31(6), 710-718.
https://doi.org/10.2341/05-145
Radović I, Vulićević Z, Garcia-Godoy F. Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin. in Operative Dentistry. 2006;31(6):710-718.
doi:10.2341/05-145 .
Radović, I., Vulićević, Zoran, Garcia-Godoy, Franklin, "Morphological evaluation of 2-and 1-step self-etching system interfaces with dentin" in Operative Dentistry, 31, no. 6 (2006):710-718,
https://doi.org/10.2341/05-145 . .
29
20
28

Temporary care in focus-temporary bridges

Todorović, Aleksandar; Vulićević, Zoran; Špadijer, Aleksandra

(Udruženje stomatologa Srbije i Crne Gore - Sekcija za stomatološku protetiku, Beograd, 2004)

TY  - JOUR
AU  - Todorović, Aleksandar
AU  - Vulićević, Zoran
AU  - Špadijer, Aleksandra
PY  - 2004
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1194
AB  - Perfect temporary care guarantees us the complete trust of our patients. From a chemical standpoint Luxatemp or Acrytemp can be classified as bis-acrylic materials. This class of materials has numerous advantages that give us many possibilities for successful clinical use: compatibility with the pulp, lowest setting temperatures, good flexural strength, low shrinkage and high abrasion resistance. The purpose of this paper is to present method of fabrication fixed provisional restorations using a vacuum formed tray matrix with new generation of temporary materials.
AB  - Adekvatno izrađene privremene nadoknade nam obezbeđuju između ostalog i sticanje pacijentovog poverenja. Luxatemp ili Acrytemp pripadaju grupi bis-akrilatnih kompozita. Ovi materijali imaju brojne prednosti: kompatibilnost sa pulpo-dentinskim kompleksom, nisku temperaturu polimerizacije, dobru otpornost na savijanje, malu kontrakciju i dobru otpornost na abraziju. Cilj ovog rada je bio da prikaže kombinovanu metodu izrade privremenih mostova upotrebom transparentnih plastičnih kalupa u kombinaciji sa novom generacijom materijala za izradu privremenih nadoknada.
PB  - Udruženje stomatologa Srbije i Crne Gore - Sekcija za stomatološku protetiku, Beograd
T2  - Stomatološka protetika
T1  - Temporary care in focus-temporary bridges
T1  - Kombinovana metoda izrade privremenih mostova
VL  - 3
IS  - 1
SP  - 21
EP  - 25
UR  - https://hdl.handle.net/21.15107/rcub_smile_1194
ER  - 
@article{
author = "Todorović, Aleksandar and Vulićević, Zoran and Špadijer, Aleksandra",
year = "2004",
abstract = "Perfect temporary care guarantees us the complete trust of our patients. From a chemical standpoint Luxatemp or Acrytemp can be classified as bis-acrylic materials. This class of materials has numerous advantages that give us many possibilities for successful clinical use: compatibility with the pulp, lowest setting temperatures, good flexural strength, low shrinkage and high abrasion resistance. The purpose of this paper is to present method of fabrication fixed provisional restorations using a vacuum formed tray matrix with new generation of temporary materials., Adekvatno izrađene privremene nadoknade nam obezbeđuju između ostalog i sticanje pacijentovog poverenja. Luxatemp ili Acrytemp pripadaju grupi bis-akrilatnih kompozita. Ovi materijali imaju brojne prednosti: kompatibilnost sa pulpo-dentinskim kompleksom, nisku temperaturu polimerizacije, dobru otpornost na savijanje, malu kontrakciju i dobru otpornost na abraziju. Cilj ovog rada je bio da prikaže kombinovanu metodu izrade privremenih mostova upotrebom transparentnih plastičnih kalupa u kombinaciji sa novom generacijom materijala za izradu privremenih nadoknada.",
publisher = "Udruženje stomatologa Srbije i Crne Gore - Sekcija za stomatološku protetiku, Beograd",
journal = "Stomatološka protetika",
title = "Temporary care in focus-temporary bridges, Kombinovana metoda izrade privremenih mostova",
volume = "3",
number = "1",
pages = "21-25",
url = "https://hdl.handle.net/21.15107/rcub_smile_1194"
}
Todorović, A., Vulićević, Z.,& Špadijer, A.. (2004). Temporary care in focus-temporary bridges. in Stomatološka protetika
Udruženje stomatologa Srbije i Crne Gore - Sekcija za stomatološku protetiku, Beograd., 3(1), 21-25.
https://hdl.handle.net/21.15107/rcub_smile_1194
Todorović A, Vulićević Z, Špadijer A. Temporary care in focus-temporary bridges. in Stomatološka protetika. 2004;3(1):21-25.
https://hdl.handle.net/21.15107/rcub_smile_1194 .
Todorović, Aleksandar, Vulićević, Zoran, Špadijer, Aleksandra, "Temporary care in focus-temporary bridges" in Stomatološka protetika, 3, no. 1 (2004):21-25,
https://hdl.handle.net/21.15107/rcub_smile_1194 .

Clinical evaluation of composite materials for pit and fissure sealing

Petrović, Vanja; Vulićević, Zoran; Marković, Dejan

(Srpsko lekarsko društvo - Stomatološka sekcija, Beograd, 2003)

TY  - JOUR
AU  - Petrović, Vanja
AU  - Vulićević, Zoran
AU  - Marković, Dejan
PY  - 2003
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1162
AB  - Sistemic fluoride ingestion has been found to be more effective in its caries- reducing benefits on the smooth surfaces than on the pit and fissures. A greater vulnerability to pit and fissure caries determines the need for occlusal surface specific protection. The objective of this study was to investigate clinical effectiveness of 5 different composite sealants during an 18- month observation period. Tested materials were: Superlux Seal-opak (composite with filler particles), Superlux Seal-transparent Estiseal and Fissurit (clear), and Fissurit F (composite with fluoride). They were evaluated according to modified Cvar&Ryge criteria for: retention (R), marginal adaptation (MA), marginal discoloration (MD), surface texture (ST), and secondary caries (SC). The materials were applied in 87 children 6-7 years of age, on 215 first permanent molars, two different materials for each patient. The results were tested for statistical significance by .2 and Fisher's T-test. The results showed good clinical performance of all tested materials with no statistically significant differences. High effectiveness in occlusal caries prevention rated from 97,30% for Fissurit F, and 98% for Superlux Sealopak, to 100% for all other tested sealants. Pit and fissure sealing is an effective prophylactic measure which should be part of the preventive program.
AB  - Sistemska primena fluorida značajno je doprinela smanjenju incidence karijesa glatkih površina zuba, ali ne i fisura i jamica. Specifičnost okluzalne morfologije zahteva dodatnu profilaktičku meru u vidu zalivanja fisura i jamica specijalno formulisanim materijalima. Cilj ovoga rada bio je ispitivanje kliničke efikasnosti 5 različitih kompozitnih materijala za zalivanje fisura u opservacionom periodu od 18 meseci. Testirani su sledeći materijali, predstavnici tri podvrste kompozitnih zalivača: Superlux Sealopak, (opakni, sa puniocem); Superlux Seal-transparent, Estiseal, i Fissurit (transparentni) i Fissurit F (sa fluorom). Modifikovanim Cvar&Ryge kriterijumima praćeni su retencija (R), marginalna adaptacija (MA), ivična prebojenost (IP,)površinska hrapavost (PH), i pojava sekundarnog karijesa (SK). U ispitivanje je uključeno 87 dece uzrasta 6-7 godina. Svakom pacijentu su na prve stalne molare aplikovana po dva različita materijala na ukupno 215 zuba. Na kraju opservacionog perioda svi testirani materijali pokazali su dobre kliničke osobine bez značajnosti statističkih razlika testiranih.2 i Fisherovim T-testom i visok stepen zaštite od karijesa (od 97,30% za Fissurit F, 98% za Superlux Seal-opak,do 100% za ostale ispitivane materijale). Zalivanje fisura je efikasna profilaktička mera i treba da bude sastavni deo preventivnog programa.
PB  - Srpsko lekarsko društvo - Stomatološka sekcija, Beograd
T2  - Stomatološki glasnik Srbije
T1  - Clinical evaluation of composite materials for pit and fissure sealing
T1  - Kliničko ispitivanje kompozitnih zalivača fisura
VL  - 50
IS  - 2
SP  - 70
EP  - 75
DO  - 10.2298/SGS0302070P
ER  - 
@article{
author = "Petrović, Vanja and Vulićević, Zoran and Marković, Dejan",
year = "2003",
abstract = "Sistemic fluoride ingestion has been found to be more effective in its caries- reducing benefits on the smooth surfaces than on the pit and fissures. A greater vulnerability to pit and fissure caries determines the need for occlusal surface specific protection. The objective of this study was to investigate clinical effectiveness of 5 different composite sealants during an 18- month observation period. Tested materials were: Superlux Seal-opak (composite with filler particles), Superlux Seal-transparent Estiseal and Fissurit (clear), and Fissurit F (composite with fluoride). They were evaluated according to modified Cvar&Ryge criteria for: retention (R), marginal adaptation (MA), marginal discoloration (MD), surface texture (ST), and secondary caries (SC). The materials were applied in 87 children 6-7 years of age, on 215 first permanent molars, two different materials for each patient. The results were tested for statistical significance by .2 and Fisher's T-test. The results showed good clinical performance of all tested materials with no statistically significant differences. High effectiveness in occlusal caries prevention rated from 97,30% for Fissurit F, and 98% for Superlux Sealopak, to 100% for all other tested sealants. Pit and fissure sealing is an effective prophylactic measure which should be part of the preventive program., Sistemska primena fluorida značajno je doprinela smanjenju incidence karijesa glatkih površina zuba, ali ne i fisura i jamica. Specifičnost okluzalne morfologije zahteva dodatnu profilaktičku meru u vidu zalivanja fisura i jamica specijalno formulisanim materijalima. Cilj ovoga rada bio je ispitivanje kliničke efikasnosti 5 različitih kompozitnih materijala za zalivanje fisura u opservacionom periodu od 18 meseci. Testirani su sledeći materijali, predstavnici tri podvrste kompozitnih zalivača: Superlux Sealopak, (opakni, sa puniocem); Superlux Seal-transparent, Estiseal, i Fissurit (transparentni) i Fissurit F (sa fluorom). Modifikovanim Cvar&Ryge kriterijumima praćeni su retencija (R), marginalna adaptacija (MA), ivična prebojenost (IP,)površinska hrapavost (PH), i pojava sekundarnog karijesa (SK). U ispitivanje je uključeno 87 dece uzrasta 6-7 godina. Svakom pacijentu su na prve stalne molare aplikovana po dva različita materijala na ukupno 215 zuba. Na kraju opservacionog perioda svi testirani materijali pokazali su dobre kliničke osobine bez značajnosti statističkih razlika testiranih.2 i Fisherovim T-testom i visok stepen zaštite od karijesa (od 97,30% za Fissurit F, 98% za Superlux Seal-opak,do 100% za ostale ispitivane materijale). Zalivanje fisura je efikasna profilaktička mera i treba da bude sastavni deo preventivnog programa.",
publisher = "Srpsko lekarsko društvo - Stomatološka sekcija, Beograd",
journal = "Stomatološki glasnik Srbije",
title = "Clinical evaluation of composite materials for pit and fissure sealing, Kliničko ispitivanje kompozitnih zalivača fisura",
volume = "50",
number = "2",
pages = "70-75",
doi = "10.2298/SGS0302070P"
}
Petrović, V., Vulićević, Z.,& Marković, D.. (2003). Clinical evaluation of composite materials for pit and fissure sealing. in Stomatološki glasnik Srbije
Srpsko lekarsko društvo - Stomatološka sekcija, Beograd., 50(2), 70-75.
https://doi.org/10.2298/SGS0302070P
Petrović V, Vulićević Z, Marković D. Clinical evaluation of composite materials for pit and fissure sealing. in Stomatološki glasnik Srbije. 2003;50(2):70-75.
doi:10.2298/SGS0302070P .
Petrović, Vanja, Vulićević, Zoran, Marković, Dejan, "Clinical evaluation of composite materials for pit and fissure sealing" in Stomatološki glasnik Srbije, 50, no. 2 (2003):70-75,
https://doi.org/10.2298/SGS0302070P . .
1

Glass-ionomer cements and compomers as a biocompatible materials

Marković, D.; Vulićević, Zoran; Vojnović, B

(Sage Publications Inc, Thousand Oaks, 1998)

TY  - CONF
AU  - Marković, D.
AU  - Vulićević, Zoran
AU  - Vojnović, B
PY  - 1998
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1094
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - Glass-ionomer cements and compomers as a biocompatible materials
VL  - 77
SP  - 932
EP  - 932
UR  - https://hdl.handle.net/21.15107/rcub_smile_1094
ER  - 
@conference{
author = "Marković, D. and Vulićević, Zoran and Vojnović, B",
year = "1998",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "Glass-ionomer cements and compomers as a biocompatible materials",
volume = "77",
pages = "932-932",
url = "https://hdl.handle.net/21.15107/rcub_smile_1094"
}
Marković, D., Vulićević, Z.,& Vojnović, B.. (1998). Glass-ionomer cements and compomers as a biocompatible materials. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 77, 932-932.
https://hdl.handle.net/21.15107/rcub_smile_1094
Marković D, Vulićević Z, Vojnović B. Glass-ionomer cements and compomers as a biocompatible materials. in Journal of Dental Research. 1998;77:932-932.
https://hdl.handle.net/21.15107/rcub_smile_1094 .
Marković, D., Vulićević, Zoran, Vojnović, B, "Glass-ionomer cements and compomers as a biocompatible materials" in Journal of Dental Research, 77 (1998):932-932,
https://hdl.handle.net/21.15107/rcub_smile_1094 .

Clinical trial of contemporary pit and fissure sealants

Petrović, V.; Beloica, Dragan; Vulović, M; Vulićević, Zoran

(Sage Publications Inc, Thousand Oaks, 1997)

TY  - CONF
AU  - Petrović, V.
AU  - Beloica, Dragan
AU  - Vulović, M
AU  - Vulićević, Zoran
PY  - 1997
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1087
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - Clinical trial of contemporary pit and fissure sealants
VL  - 76
SP  - 226
EP  - 226
UR  - https://hdl.handle.net/21.15107/rcub_smile_1087
ER  - 
@conference{
author = "Petrović, V. and Beloica, Dragan and Vulović, M and Vulićević, Zoran",
year = "1997",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "Clinical trial of contemporary pit and fissure sealants",
volume = "76",
pages = "226-226",
url = "https://hdl.handle.net/21.15107/rcub_smile_1087"
}
Petrović, V., Beloica, D., Vulović, M.,& Vulićević, Z.. (1997). Clinical trial of contemporary pit and fissure sealants. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 76, 226-226.
https://hdl.handle.net/21.15107/rcub_smile_1087
Petrović V, Beloica D, Vulović M, Vulićević Z. Clinical trial of contemporary pit and fissure sealants. in Journal of Dental Research. 1997;76:226-226.
https://hdl.handle.net/21.15107/rcub_smile_1087 .
Petrović, V., Beloica, Dragan, Vulović, M, Vulićević, Zoran, "Clinical trial of contemporary pit and fissure sealants" in Journal of Dental Research, 76 (1997):226-226,
https://hdl.handle.net/21.15107/rcub_smile_1087 .

A clinical trial of two compomer systems

Vulićević, Zoran; Beloica, Dragan; Vulović, M

(Sage Publications Inc, Thousand Oaks, 1997)

TY  - CONF
AU  - Vulićević, Zoran
AU  - Beloica, Dragan
AU  - Vulović, M
PY  - 1997
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1085
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - A clinical trial of two compomer systems
VL  - 76
SP  - 1211
EP  - 1211
UR  - https://hdl.handle.net/21.15107/rcub_smile_1085
ER  - 
@conference{
author = "Vulićević, Zoran and Beloica, Dragan and Vulović, M",
year = "1997",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "A clinical trial of two compomer systems",
volume = "76",
pages = "1211-1211",
url = "https://hdl.handle.net/21.15107/rcub_smile_1085"
}
Vulićević, Z., Beloica, D.,& Vulović, M.. (1997). A clinical trial of two compomer systems. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 76, 1211-1211.
https://hdl.handle.net/21.15107/rcub_smile_1085
Vulićević Z, Beloica D, Vulović M. A clinical trial of two compomer systems. in Journal of Dental Research. 1997;76:1211-1211.
https://hdl.handle.net/21.15107/rcub_smile_1085 .
Vulićević, Zoran, Beloica, Dragan, Vulović, M, "A clinical trial of two compomer systems" in Journal of Dental Research, 76 (1997):1211-1211,
https://hdl.handle.net/21.15107/rcub_smile_1085 .
1

Clinical evaluation of pit and fissure sealants

Petrović, V.; Vulović, M; Vulićević, Zoran

(Sage Publications Inc, Thousand Oaks, 1996)

TY  - CONF
AU  - Petrović, V.
AU  - Vulović, M
AU  - Vulićević, Zoran
PY  - 1996
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1068
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - Clinical evaluation of pit and fissure sealants
VL  - 75
SP  - 2153
EP  - 2153
UR  - https://hdl.handle.net/21.15107/rcub_smile_1068
ER  - 
@conference{
author = "Petrović, V. and Vulović, M and Vulićević, Zoran",
year = "1996",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "Clinical evaluation of pit and fissure sealants",
volume = "75",
pages = "2153-2153",
url = "https://hdl.handle.net/21.15107/rcub_smile_1068"
}
Petrović, V., Vulović, M.,& Vulićević, Z.. (1996). Clinical evaluation of pit and fissure sealants. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 75, 2153-2153.
https://hdl.handle.net/21.15107/rcub_smile_1068
Petrović V, Vulović M, Vulićević Z. Clinical evaluation of pit and fissure sealants. in Journal of Dental Research. 1996;75:2153-2153.
https://hdl.handle.net/21.15107/rcub_smile_1068 .
Petrović, V., Vulović, M, Vulićević, Zoran, "Clinical evaluation of pit and fissure sealants" in Journal of Dental Research, 75 (1996):2153-2153,
https://hdl.handle.net/21.15107/rcub_smile_1068 .
4

Clinical evaluation of two composite systems

Vulićević, Zoran; Andelković, SM

(Sage Publications Inc, Thousand Oaks, 1996)

TY  - CONF
AU  - Vulićević, Zoran
AU  - Andelković, SM
PY  - 1996
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1069
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - Clinical evaluation of two composite systems
VL  - 75
SP  - 2154
EP  - 2154
UR  - https://hdl.handle.net/21.15107/rcub_smile_1069
ER  - 
@conference{
author = "Vulićević, Zoran and Andelković, SM",
year = "1996",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "Clinical evaluation of two composite systems",
volume = "75",
pages = "2154-2154",
url = "https://hdl.handle.net/21.15107/rcub_smile_1069"
}
Vulićević, Z.,& Andelković, S.. (1996). Clinical evaluation of two composite systems. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 75, 2154-2154.
https://hdl.handle.net/21.15107/rcub_smile_1069
Vulićević Z, Andelković S. Clinical evaluation of two composite systems. in Journal of Dental Research. 1996;75:2154-2154.
https://hdl.handle.net/21.15107/rcub_smile_1069 .
Vulićević, Zoran, Andelković, SM, "Clinical evaluation of two composite systems" in Journal of Dental Research, 75 (1996):2154-2154,
https://hdl.handle.net/21.15107/rcub_smile_1069 .

Tensile bond strength of resin bonding and polycarboxylate cements

Vulićević, Zoran; Beloica, Dragan; Vulović, M

(Sage Publications Inc, Thousand Oaks, 1996)

TY  - CONF
AU  - Vulićević, Zoran
AU  - Beloica, Dragan
AU  - Vulović, M
PY  - 1996
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1067
PB  - Sage Publications Inc, Thousand Oaks
C3  - Journal of Dental Research
T1  - Tensile bond strength of resin bonding and polycarboxylate cements
VL  - 75
SP  - 43
EP  - 43
UR  - https://hdl.handle.net/21.15107/rcub_smile_1067
ER  - 
@conference{
author = "Vulićević, Zoran and Beloica, Dragan and Vulović, M",
year = "1996",
publisher = "Sage Publications Inc, Thousand Oaks",
journal = "Journal of Dental Research",
title = "Tensile bond strength of resin bonding and polycarboxylate cements",
volume = "75",
pages = "43-43",
url = "https://hdl.handle.net/21.15107/rcub_smile_1067"
}
Vulićević, Z., Beloica, D.,& Vulović, M.. (1996). Tensile bond strength of resin bonding and polycarboxylate cements. in Journal of Dental Research
Sage Publications Inc, Thousand Oaks., 75, 43-43.
https://hdl.handle.net/21.15107/rcub_smile_1067
Vulićević Z, Beloica D, Vulović M. Tensile bond strength of resin bonding and polycarboxylate cements. in Journal of Dental Research. 1996;75:43-43.
https://hdl.handle.net/21.15107/rcub_smile_1067 .
Vulićević, Zoran, Beloica, Dragan, Vulović, M, "Tensile bond strength of resin bonding and polycarboxylate cements" in Journal of Dental Research, 75 (1996):43-43,
https://hdl.handle.net/21.15107/rcub_smile_1067 .