TY  - JOUR
AU  - Rudolf, Rebeka
AU  - Zupančič-Hartner, Tjaša
AU  - Kosec, L.
AU  - Todorović, A.
AU  - Kosec, Borut
AU  - Anžel, Ivan
PY  - 2008
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1440
AB  - Development of a dental alloy with high Au content is based on the ternary system of Au-Pt-Zn with a nominal composition of 86,9Au-9,9Pt-1,5Zn, and about 1,5 wt.% micro-alloying elements (in, Ir, Rh). The results analyses of different heat-treated states showed that the optimal mechanical properties and hardness of an Au-Pt-Zn alloy can be reached with combinations of heat treatment for 20 minutes at 723 K and then slowly cooling, if the alloy was annealed at 1223 K for 30 minutes and the water quenched. Research results confirmed that the microstructure of the Au-Pt-Zn alloy consists of two phases: alpha(1)-phase rich in Au (main phase) and alpha(2)-phase rich in Pt (minor phase). During XRD analysis and use of the Rietveld method, it was found that the alpha(1)-phase content is about 98,5 wt.% while the content of alpha(2)-phase is 1,5 wt.%. STA analyses show that the Au-Pt-Zn alloy has a solidus temperature of about 1292 K and a liquidus temperature of about 1412 K.
PB  - Croatian Metallurgical Society
T2  - Metalurgija
T1  - Mechanical properties and microstructure characterisation of Au-Pt dental alloy
VL  - 47
IS  - 4
SP  - 317
EP  - 323
UR  - https://hdl.handle.net/21.15107/rcub_smile_1440
ER  - 

@article{
author = "Rudolf, Rebeka and Zupančič-Hartner, Tjaša and Kosec, L. and Todorović, A. and Kosec, Borut and Anžel, Ivan",
year = "2008",
abstract = "Development of a dental alloy with high Au content is based on the ternary system of Au-Pt-Zn with a nominal composition of 86,9Au-9,9Pt-1,5Zn, and about 1,5 wt.% micro-alloying elements (in, Ir, Rh). The results analyses of different heat-treated states showed that the optimal mechanical properties and hardness of an Au-Pt-Zn alloy can be reached with combinations of heat treatment for 20 minutes at 723 K and then slowly cooling, if the alloy was annealed at 1223 K for 30 minutes and the water quenched. Research results confirmed that the microstructure of the Au-Pt-Zn alloy consists of two phases: alpha(1)-phase rich in Au (main phase) and alpha(2)-phase rich in Pt (minor phase). During XRD analysis and use of the Rietveld method, it was found that the alpha(1)-phase content is about 98,5 wt.% while the content of alpha(2)-phase is 1,5 wt.%. STA analyses show that the Au-Pt-Zn alloy has a solidus temperature of about 1292 K and a liquidus temperature of about 1412 K.",
publisher = "Croatian Metallurgical Society",
journal = "Metalurgija",
title = "Mechanical properties and microstructure characterisation of Au-Pt dental alloy",
volume = "47",
number = "4",
pages = "317-323",
url = "https://hdl.handle.net/21.15107/rcub_smile_1440"
}

Rudolf, R., Zupančič-Hartner, T., Kosec, L., Todorović, A., Kosec, B.,& Anžel, I.. (2008). Mechanical properties and microstructure characterisation of Au-Pt dental alloy. in Metalurgija
Croatian Metallurgical Society., 47(4), 317-323.
https://hdl.handle.net/21.15107/rcub_smile_1440

Rudolf R, Zupančič-Hartner T, Kosec L, Todorović A, Kosec B, Anžel I. Mechanical properties and microstructure characterisation of Au-Pt dental alloy. in Metalurgija. 2008;47(4):317-323.
https://hdl.handle.net/21.15107/rcub_smile_1440 .

Rudolf, Rebeka, Zupančič-Hartner, Tjaša, Kosec, L., Todorović, A., Kosec, Borut, Anžel, Ivan, "Mechanical properties and microstructure characterisation of Au-Pt dental alloy" in Metalurgija, 47, no. 4 (2008):317-323,
https://hdl.handle.net/21.15107/rcub_smile_1440 .

TY  - JOUR
AU  - Rudolf, Rebeka
AU  - Kramberger, Janez
AU  - Zupančič-Hartner, Tjaša
AU  - Marić-Dragaš, Aleksandra
AU  - Lazić, Vojkan
PY  - 2006
UR  - https://smile.stomf.bg.ac.rs/handle/123456789/1293
AB  - Introduction: Porcelain to metal fused alloys with Au content are most frequently used in dentistry. Their characteristic is high biocompatibility and well fusion to ceramics. Aim of the study: The aim of this study was to present the procedure of production and technology of developing the new dental alloy with high gold content (Au). Materials and Methods: The dental alloy was melted and cast in a vacuum-induction melting furnace. Casting was followed by subsequent thermo-mechanical treatments (the procedures of profile and polish milling, and thermal treatment) and the cutting strips into regular shapes. Testing of the new Au dental alloy included an examination of alloy’s final condition. The measurement of hardness was carried out according to standard 6507-1:1998, and static tensile testing was performed for determination of the mechanical properties. Microscopic analysis of the dental alloy and the finished metal-ceramic bridge included an observation of the polished surface, and by performing qualitative and quantitative micro-chemical analyses. Results: The mechanical properties and hardness of new dental gold alloy was: Rp0.=630 [N/mm2], Rm =710 [N/mm2], A= 9%, 170 HV and CTE (25-600°C) about 14,55×10-6K-1. Macro-inspection of the finished metalceramic bridge showed that there was no porosity. However, during scanning electron microscopic examination, one of the tested sample shows porosity in one alloy region and in the ceramic layer. Detailed examination of the ceramic layer’s surface showed that there were two types of air or gas bubbles - larger with distinct bubbles (type I) and smaller with clearly porous microstructure (type II). Conclusions: According to the results of this study, it can be concluded that this new dental alloy from Zlatarna Celje satisfied all the required standards regarding mechanical properties and hardness. The application of new dental alloy with high gold content depends on the adequate technology when firing ceramics. It is necessary to obtain accurate oxidation temperature and cooling rates of metal-ceramic restorations because, otherwise, different defects may appear.
AB  - Uvod: Visoko plemenite legure za metal-keramiku (PFM legure - porcelain fused to metal alloy) su najviše korišćene legure u stomatologiji a odlikuje ih visoka biološka prihvatljivost i dobro vezivanje sa keramikom. Cilj: Cilj ovog rada bio je da prikaže postupak dobijanja i tehnologiju razvoja i izrade nove dentalne legure sa visokim sadržajem zlata (Au). Materijal i metod: Pretapanje komponenti dentalne legure izvedeno je u vakuumskoj peći. Tome je sledila naknadna termo-mehanička obrada odlivka (postupcima profilnog i polirnog valjanja, toplotna obrada) kao i sečenje dobijene trake u propisani oblik. Testiranje nove Au dentalne legure uključivalo je testiranje izlaznog stanja legure. Merenje tvrdoće sprovedeno je po standardu 6507-1:1998, dok je za određivanje mehaničkih karakteristika upotrebljeno statično istezanje. Mikroskopska analiza dentalnih legura i završenog metal-keramičkog mosta uključivala je posmatranje polirane površine i izvođenje kvalitativne i kvantitativne mikro-hemijske analize. Rezultati: Mehaničke karakteristike i tvrdoća nove dentalne legure sa visokim sadržajem zlata iznosi Rp0.=630 [N/mm2], Rm =710 [N/mm2], A= 9%, 170 HV, a CTE (25-600°C) iznosi oko 14,55×10-6K-1. Makroskopski na površini metala i potom sinterovane keramike nije uočena poroznost dok je mikroskopskim pregledom ustanovljeno da je na pojedinim mestima jednog uzorka vidna poroznost metalne konstrukcije mosta kao i keramičke površine u vidu većih mehurića (tip I) i manjih sa izrazito poroznom mikrostrukturom (tip II). Zaključak: Na osnovu dobijenih rezultata može se zaključiti, da nova dentalna legura Zlatarne Celje odgovara propisanim standardima u pogledu mehaničkih karakteristika i tvrdoće. Neophodno je primeniti pravilnu temperaturu oksidacije i režim hlađenja fiksne zubne nadoknade, jer u suprotnom može doći do nastanka različitih defekata.
PB  - Srpsko lekarsko društvo - Stomatološka sekcija, Beograd
T2  - Stomatološki glasnik Srbije
T1  - New gold dental alloy for metal-ceramic restorations
T1  - Nova zlatna dentalna legura za metalkeramiku
VL  - 53
IS  - 4
SP  - 236
EP  - 245
DO  - 10.2298/SGS0604236R
ER  - 

@article{
author = "Rudolf, Rebeka and Kramberger, Janez and Zupančič-Hartner, Tjaša and Marić-Dragaš, Aleksandra and Lazić, Vojkan",
year = "2006",
abstract = "Introduction: Porcelain to metal fused alloys with Au content are most frequently used in dentistry. Their characteristic is high biocompatibility and well fusion to ceramics. Aim of the study: The aim of this study was to present the procedure of production and technology of developing the new dental alloy with high gold content (Au). Materials and Methods: The dental alloy was melted and cast in a vacuum-induction melting furnace. Casting was followed by subsequent thermo-mechanical treatments (the procedures of profile and polish milling, and thermal treatment) and the cutting strips into regular shapes. Testing of the new Au dental alloy included an examination of alloy’s final condition. The measurement of hardness was carried out according to standard 6507-1:1998, and static tensile testing was performed for determination of the mechanical properties. Microscopic analysis of the dental alloy and the finished metal-ceramic bridge included an observation of the polished surface, and by performing qualitative and quantitative micro-chemical analyses. Results: The mechanical properties and hardness of new dental gold alloy was: Rp0.=630 [N/mm2], Rm =710 [N/mm2], A= 9%, 170 HV and CTE (25-600°C) about 14,55×10-6K-1. Macro-inspection of the finished metalceramic bridge showed that there was no porosity. However, during scanning electron microscopic examination, one of the tested sample shows porosity in one alloy region and in the ceramic layer. Detailed examination of the ceramic layer’s surface showed that there were two types of air or gas bubbles - larger with distinct bubbles (type I) and smaller with clearly porous microstructure (type II). Conclusions: According to the results of this study, it can be concluded that this new dental alloy from Zlatarna Celje satisfied all the required standards regarding mechanical properties and hardness. The application of new dental alloy with high gold content depends on the adequate technology when firing ceramics. It is necessary to obtain accurate oxidation temperature and cooling rates of metal-ceramic restorations because, otherwise, different defects may appear., Uvod: Visoko plemenite legure za metal-keramiku (PFM legure - porcelain fused to metal alloy) su najviše korišćene legure u stomatologiji a odlikuje ih visoka biološka prihvatljivost i dobro vezivanje sa keramikom. Cilj: Cilj ovog rada bio je da prikaže postupak dobijanja i tehnologiju razvoja i izrade nove dentalne legure sa visokim sadržajem zlata (Au). Materijal i metod: Pretapanje komponenti dentalne legure izvedeno je u vakuumskoj peći. Tome je sledila naknadna termo-mehanička obrada odlivka (postupcima profilnog i polirnog valjanja, toplotna obrada) kao i sečenje dobijene trake u propisani oblik. Testiranje nove Au dentalne legure uključivalo je testiranje izlaznog stanja legure. Merenje tvrdoće sprovedeno je po standardu 6507-1:1998, dok je za određivanje mehaničkih karakteristika upotrebljeno statično istezanje. Mikroskopska analiza dentalnih legura i završenog metal-keramičkog mosta uključivala je posmatranje polirane površine i izvođenje kvalitativne i kvantitativne mikro-hemijske analize. Rezultati: Mehaničke karakteristike i tvrdoća nove dentalne legure sa visokim sadržajem zlata iznosi Rp0.=630 [N/mm2], Rm =710 [N/mm2], A= 9%, 170 HV, a CTE (25-600°C) iznosi oko 14,55×10-6K-1. Makroskopski na površini metala i potom sinterovane keramike nije uočena poroznost dok je mikroskopskim pregledom ustanovljeno da je na pojedinim mestima jednog uzorka vidna poroznost metalne konstrukcije mosta kao i keramičke površine u vidu većih mehurića (tip I) i manjih sa izrazito poroznom mikrostrukturom (tip II). Zaključak: Na osnovu dobijenih rezultata može se zaključiti, da nova dentalna legura Zlatarne Celje odgovara propisanim standardima u pogledu mehaničkih karakteristika i tvrdoće. Neophodno je primeniti pravilnu temperaturu oksidacije i režim hlađenja fiksne zubne nadoknade, jer u suprotnom može doći do nastanka različitih defekata.",
publisher = "Srpsko lekarsko društvo - Stomatološka sekcija, Beograd",
journal = "Stomatološki glasnik Srbije",
title = "New gold dental alloy for metal-ceramic restorations, Nova zlatna dentalna legura za metalkeramiku",
volume = "53",
number = "4",
pages = "236-245",
doi = "10.2298/SGS0604236R"
}

Rudolf, R., Kramberger, J., Zupančič-Hartner, T., Marić-Dragaš, A.,& Lazić, V.. (2006). New gold dental alloy for metal-ceramic restorations. in Stomatološki glasnik Srbije
Srpsko lekarsko društvo - Stomatološka sekcija, Beograd., 53(4), 236-245.
https://doi.org/10.2298/SGS0604236R

Rudolf R, Kramberger J, Zupančič-Hartner T, Marić-Dragaš A, Lazić V. New gold dental alloy for metal-ceramic restorations. in Stomatološki glasnik Srbije. 2006;53(4):236-245.
doi:10.2298/SGS0604236R .

Rudolf, Rebeka, Kramberger, Janez, Zupančič-Hartner, Tjaša, Marić-Dragaš, Aleksandra, Lazić, Vojkan, "New gold dental alloy for metal-ceramic restorations" in Stomatološki glasnik Srbije, 53, no. 4 (2006):236-245,
https://doi.org/10.2298/SGS0604236R . .