Претраживање
Приказ резултата 1-10 од 49
Monomer elution from nanohybrid and ormocer-based composites cured with different light sources
(Elsevier Sci Ltd, Oxford, 2011)
Objectives. To study monomer elution from four resin-based composites (RBCs) cured with different light sources. Methods. Twenty-eight premolars were randomly allocated to four groups. Standardized cavities were prepared ...
Prevalence and Data Availability of Early Childhood Caries in 93 United Nations Countries, 2007-2017
(Amer Public Health Assoc Inc, Washington, 2018)
Objectives. To assess the relationship between health care system and economic factors and early childhood caries (ECC) data availability and prevalence. Methods. We estimated ECC data for 193 United Nations countries from ...
A 1-Year Prospective Clinical and Radiographic Study of Early-Loaded Bone Level Implants in the Posterior Maxilla
(Wiley-Blackwell, Hoboken, 2015)
PurposesThe primary aim of the study was to investigate a 1-year success rate of early-loaded bone level implants with a chemically modified sand-blasted, large grit, acid-etched surface (SLActive (R), Institut Straumann ...
Monomer-to-polymer conversion and micro-tensile bond strength to dentine of experimental and commercial adhesives containing diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide or a camphorquinone/amine photo-initiator system
(Elsevier Sci Ltd, Oxford, 2013)
Objectives: To compare the degree of conversion (DC) of adhesives initiated by diphenyl(2,4,6-trimethylbenzoyl) phosphine oxide (TPO) or a camphorquinone/tertiary amine system (CQ/Amine) as well as their 'immediate' ...
Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED units
(Elsevier Sci Ltd, Oxford, 2012)
Objectives: To determine the degree of conversion (DC) over 48 h post-curing of resin mixtures containing trimethylbenzoyl-diphenylphosphine oxide (TPO) initiator cured by a polywave or a monowave LED light-curing unit ...
Ferrule Effect: A Literature Review
(Elsevier Science Inc, New York, 2012)
Introduction: Preserving intact coronal and radicular tooth structure, especially maintaining cervical tissue to create a ferrule effect, is considered to be crucial for the optimal biomechanical behavior of restored teeth. ...
Real-time thermographic analysis of low-density bone during implant placement: a randomized parallel-group clinical study comparing lateral condensation with bone drilling surgical technique
(Wiley, Hoboken, 2014)
Objectives: To compare the effect of two surgical techniques, lateral condensation and bone drilling, on changes in temperature of the adjacent low-density bone during implant placement into posterior maxilla and to ...
The influence of three different apical implant designs at stability and osseointegration process: experimental study in rabbits
(Wiley, Hoboken, 2017)
Objectives: The aim of this study was to perform a histomorphometric and biomechanical comparison of three implants with different designs of the apical area to promote a better bone initial stability and its correlation ...
Randomized clinical study of the peri-implant healing to hydrophilic and hydrophobic implant surfaces in patients receiving anticoagulants
(Wiley, Hoboken, 2017)
ObjectivesTo compare the peri-implant bone healing between TiZr implants with hydrophilic SLActive and hydrophobic SLA implant surface in patients receiving anticoagulants, to assess the implant survival and success rate, ...
The effect of ferrule height on stress distribution within a tooth restored with fibre posts and ceramic crown: A finite element analysis
(Elsevier Sci Ltd, Oxford, 2014)
Objectives. To evaluate via finite element analysis the effect of different ferrule heights on stress distribution within each part of a maxillary first premolar (MFP) restored with adhesively luted glass fiber-reinforced ...